Allowable tensile stress in plate given tearing strength of rivet Calculator

✖Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.ⓘ Tearing strength [T_strength]			+10% -10%
✖Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.ⓘ Pitch of Rivet [p]			+10% -10%
✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Rivet Diameter [D_rivet]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.ⓘ Allowable tensile stress in plate given tearing strength of rivet [σ_t]

⎘ Copy

👎

Formula

✖

Allowable tensile stress in plate given tearing strength of rivet

Formula

`"σ"_{"t"} = "T"_{"strength"}/(("p"-"D"_{"rivet"})*"t"_{"plate"})`

Example

`"166.6667MPa"="4kN"/(("20mm"-"18mm")*"12mm")`

Calculator

LaTeX

Reset

👍

Download Strength of Materials Formula PDF

Allowable tensile stress in plate given tearing strength of rivet Solution

STEP 0: Pre-Calculation Summary

Formula Used

Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate)
σ_t = T_strength/((p-D_rivet)*t_plate)
This formula uses 5 Variables

Variables Used

Tensile Stress - (Measured in Pascal) - Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force.
Tearing strength - (Measured in Newton) - Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions.
Pitch of Rivet - (Measured in Meter) - Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Tearing strength: 4 Kilonewton --> 4000 Newton (Check conversion here)
Pitch of Rivet: 20 Millimeter --> 0.02 Meter (Check conversion here)
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

σ_t = T_strength/((p-D_rivet)*t_plate) --> 4000/((0.02-0.018)*0.012)

Evaluating ... ...

σ_t = 166666666.666667

STEP 3: Convert Result to Output's Unit

166666666.666667 Pascal -->166.666666666667 Megapascal (Check conversion here)

FINAL ANSWER

166.666666666667 ≈ 166.6667 Megapascal <-- Tensile Stress

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Allowable Stress » Allowable tensile stress in plate given tearing strength of rivet

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< 9 Allowable Stress Calculators

Allowable tensile stress in plates given efficiency of riveted joint

Go Tensile Stress = Least Value of Strength/(Pitch of Rivet*Thickness of Plate*Efficiency of riveted joint)

Allowable crushing stress of rivet material given crushing strength for 'n' number of rivets

Go Crushing stress = Crushing strength/(Number of Rivets Per Pitch*Rivet Diameter*Thickness of Plate)

Allowable shear stress of rivet material given shearing strength if rivet is in double shear

Go Shear Stress in Joint = Shear Strength/(2*Number of Rivets Per Pitch*(pi/4)*(Rivet Diameter^2))

Allowable shear stress of rivet material given shearing strength if rivet is in single shear

Go Shear Stress in Joint = Shear Strength/(1*Number of Rivets Per Pitch*(pi/4)*(Rivet Diameter^2))

Allowable tensile stress in plate given tearing strength of rivet

Go Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate)

Allowable tensile stress in plate given strength of solid plate per pitch length

Go Tensile Stress = Strength of solid plate/(Pitch of Rivet*Thickness of Plate)

Allowable crushing stress of rivet material given crushing strength for double rivet

Go Crushing stress = Crushing strength/(2*Rivet Diameter*Thickness of Plate)

Allowable crushing stress of rivet material given crushing strength for single rivet

Go Crushing stress = Crushing strength/(1*Rivet Diameter*Thickness of Plate)

Allowable crushing stress of rivet material given crushing strength for triple rivet

Go Crushing stress = Crushing strength/(3*Rivet Diameter*Thickness of Plate)

Allowable tensile stress in plate given tearing strength of rivet Formula

Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate)
σ_t = T_strength/((p-D_rivet)*t_plate)

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Allowable tensile stress in plate given tearing strength of rivet?

Allowable tensile stress in plate given tearing strength of rivet calculator uses Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate) to calculate the Tensile Stress, Allowable tensile stress in plate given tearing strength of rivet refers to cases where a deforming force is applied at right angles to a surface. Tensile Stress is denoted by σ_t symbol.

How to calculate Allowable tensile stress in plate given tearing strength of rivet using this online calculator? To use this online calculator for Allowable tensile stress in plate given tearing strength of rivet, enter Tearing strength (T_strength), Pitch of Rivet (p), Rivet Diameter (D_rivet) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Allowable tensile stress in plate given tearing strength of rivet calculation can be explained with given input values -> -8.3E-5 = 4000/((0.02-0.018)*0.012).

FAQ

What is Allowable tensile stress in plate given tearing strength of rivet?

Allowable tensile stress in plate given tearing strength of rivet refers to cases where a deforming force is applied at right angles to a surface and is represented as σ_t = T_strength/((p-D_rivet)*t_plate) or Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate). Tearing strength is defined as the force required to start or to continue to tear a fabric, in either weft or warp direction, under specified conditions, Pitch of Rivet is defined as the distance between the centers of adjacent rivets that hold together the parts of a built member, Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Allowable tensile stress in plate given tearing strength of rivet?

Allowable tensile stress in plate given tearing strength of rivet refers to cases where a deforming force is applied at right angles to a surface is calculated using Tensile Stress = Tearing strength/((Pitch of Rivet-Rivet Diameter)*Thickness of Plate). To calculate Allowable tensile stress in plate given tearing strength of rivet, you need Tearing strength (T_strength), Pitch of Rivet (p), Rivet Diameter (D_rivet) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Tearing strength, Pitch of Rivet, Rivet Diameter & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Tensile Stress?

In this formula, Tensile Stress uses Tearing strength, Pitch of Rivet, Rivet Diameter & Thickness of Plate. We can use 2 other way(s) to calculate the same, which is/are as follows -

Tensile Stress = Strength of solid plate/(Pitch of Rivet*Thickness of Plate)
Tensile Stress = Least Value of Strength/(Pitch of Rivet*Thickness of Plate*Efficiency of riveted joint)

Home

FREE PDFs

🔍 Search