Boiling Point of Electrolyte during Electrochemical Machining of Metals Calculator

✖Ambient Air Temperature is the temperature where the ramming process starts.ⓘ Ambient Air Temperature [θ_o]			+10% -10%
✖Electric current is the rate of flow of electric charge through a circuit, measured in amperes.ⓘ Electric Current [I]			+10% -10%
✖Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.ⓘ Resistance of Gap Between Work and Tool [R]			+10% -10%
✖The Density of Electrolyte shows the denseness of that electrolyte in a specific given area. This is taken as mass per unit volume of a given object.ⓘ Density of Electrolyte [ρ_e]			+10% -10%
✖Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.ⓘ Specific Heat Capacity of Electrolyte [c_e]			+10% -10%
✖Volume Flow Rate is the volume of fluid that passes per unit of time.ⓘ Volume Flow Rate [q]			+10% -10%

✖Boiling Point of electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.ⓘ Boiling Point of Electrolyte during Electrochemical Machining of Metals [θ_B]

⎘ Copy

👎

Formula

✖

Boiling Point of Electrolyte during Electrochemical Machining of Metals

Formula

`"θ"_{"B"} = "θ"_{"o"}+("I"^2*"R")/("ρ"_{"e"}*"c"_{"e"}*"q")`

Example

`"368.15K"="308.15K"+(("1000A")^2*"0.012Ω")/("997kg/m³"*"4.18kJ/kg*K"*"47990.86mm³/s")`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF

Boiling Point of Electrolyte during Electrochemical Machining of Metals Solution

STEP 0: Pre-Calculation Summary

Formula Used

Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate)
θ_B = θ_o+(I^2*R)/(ρ_e*c_e*q)
This formula uses 7 Variables

Variables Used

Boiling Point of Electrolyte - (Measured in Kelvin) - Boiling Point of electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.
Ambient Air Temperature - (Measured in Kelvin) - Ambient Air Temperature is the temperature where the ramming process starts.
Electric Current - (Measured in Ampere) - Electric current is the rate of flow of electric charge through a circuit, measured in amperes.
Resistance of Gap Between Work and Tool - (Measured in Ohm) - Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.
Density of Electrolyte - (Measured in Kilogram per Cubic Meter) - The Density of Electrolyte shows the denseness of that electrolyte in a specific given area. This is taken as mass per unit volume of a given object.
Specific Heat Capacity of Electrolyte - (Measured in Joule per Kilogram per K) - Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.
Volume Flow Rate - (Measured in Cubic Meter per Second) - Volume Flow Rate is the volume of fluid that passes per unit of time.

STEP 1: Convert Input(s) to Base Unit

Ambient Air Temperature: 308.15 Kelvin --> 308.15 Kelvin No Conversion Required
Electric Current: 1000 Ampere --> 1000 Ampere No Conversion Required
Resistance of Gap Between Work and Tool: 0.012 Ohm --> 0.012 Ohm No Conversion Required
Density of Electrolyte: 997 Kilogram per Cubic Meter --> 997 Kilogram per Cubic Meter No Conversion Required
Specific Heat Capacity of Electrolyte: 4.18 Kilojoule per Kilogram per K --> 4180 Joule per Kilogram per K (Check conversion here)
Volume Flow Rate: 47990.86 Cubic Millimeter per Second --> 4.799086E-05 Cubic Meter per Second (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

θ_B = θ_o+(I^2*R)/(ρ_e*c_e*q) --> 308.15+(1000^2*0.012)/(997*4180*4.799086E-05)

Evaluating ... ...

θ_B = 368.15000317532

STEP 3: Convert Result to Output's Unit

368.15000317532 Kelvin --> No Conversion Required

FINAL ANSWER

368.15000317532 ≈ 368.15 Kelvin <-- Boiling Point of Electrolyte

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Heat in Electrolyte » Boiling Point of Electrolyte during Electrochemical Machining of Metals

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< 10+ Heat in Electrolyte Calculators

Ambient Temperature during ECM

Go Ambient Air Temperature = Boiling Point of Electrolyte-(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Maximum Volume Flow Rate)

Specific Heat of Electrolyte from Volume Flow Rate

Go Specific Heat Capacity of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Volume Flow Rate*(Boiling Point of Electrolyte-Ambient Air Temperature))

Boiling Point of Electrolyte during Electrochemical Machining of Metals

Go Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate)

Ambient Temperature

Go Ambient Air Temperature = Boiling Point of Electrolyte-Heat Absorption of Electrolyte/(Maximum Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte)

Flow Rate of Electrolyte from Heat Absorbed Electrolyte

Go Volume Flow Rate = Heat Absorption of Electrolyte/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Density of Electrolyte from Heat Absorbed Electrolyte

Go Density of Electrolyte = Heat Absorption of Electrolyte/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Specific Heat of Electrolyte

Go Specific Heat Capacity of Electrolyte = Heat Absorption of Electrolyte/(Volume Flow Rate*Density of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Heat Absorbed by Electrolyte

Go Heat Absorption of Electrolyte = Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)

Boiling Point of Electrolyte

Go Boiling Point of Electrolyte = Ambient Air Temperature+Heat Absorption of Electrolyte/(Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte)

Supply Voltage given Specific Resistivity of Electrolyte

Go Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration

Boiling Point of Electrolyte during Electrochemical Machining of Metals Formula

What is Faraday's I law of electrolysis ?

The first law of Faraday’s electrolysis states that the chemical change produced during electrolysis is proportional to the current passed and the electrochemical equivalence of the anode material.

How to Calculate Boiling Point of Electrolyte during Electrochemical Machining of Metals?

Boiling Point of Electrolyte during Electrochemical Machining of Metals calculator uses Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate) to calculate the Boiling Point of Electrolyte, The boiling point of electrolyte during Electrochemical Machining of metals formula is defined as the temperature at which the conversion of liquid to vapor state begins at a given pressure. Boiling Point of Electrolyte is denoted by θ_B symbol.

How to calculate Boiling Point of Electrolyte during Electrochemical Machining of Metals using this online calculator? To use this online calculator for Boiling Point of Electrolyte during Electrochemical Machining of Metals, enter Ambient Air Temperature (θ_o), Electric Current (I), Resistance of Gap Between Work and Tool (R), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e) & Volume Flow Rate (q) and hit the calculate button. Here is how the Boiling Point of Electrolyte during Electrochemical Machining of Metals calculation can be explained with given input values -> 60421.97 = 308.15+(1000^2*0.012)/(997*4180*4.799086E-05).

FAQ

What is Boiling Point of Electrolyte during Electrochemical Machining of Metals?

The boiling point of electrolyte during Electrochemical Machining of metals formula is defined as the temperature at which the conversion of liquid to vapor state begins at a given pressure and is represented as θ_B = θ_o+(I^2*R)/(ρ_e*c_e*q) or Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate). Ambient Air Temperature is the temperature where the ramming process starts, Electric current is the rate of flow of electric charge through a circuit, measured in amperes, Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry, The Density of Electrolyte shows the denseness of that electrolyte in a specific given area. This is taken as mass per unit volume of a given object, Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount & Volume Flow Rate is the volume of fluid that passes per unit of time.

How to calculate Boiling Point of Electrolyte during Electrochemical Machining of Metals?

The boiling point of electrolyte during Electrochemical Machining of metals formula is defined as the temperature at which the conversion of liquid to vapor state begins at a given pressure is calculated using Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate). To calculate Boiling Point of Electrolyte during Electrochemical Machining of Metals, you need Ambient Air Temperature (θ_o), Electric Current (I), Resistance of Gap Between Work and Tool (R), Density of Electrolyte (ρ_e), Specific Heat Capacity of Electrolyte (c_e) & Volume Flow Rate (q). With our tool, you need to enter the respective value for Ambient Air Temperature, Electric Current, Resistance of Gap Between Work and Tool, Density of Electrolyte, Specific Heat Capacity of Electrolyte & Volume Flow Rate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Boiling Point of Electrolyte?

In this formula, Boiling Point of Electrolyte uses Ambient Air Temperature, Electric Current, Resistance of Gap Between Work and Tool, Density of Electrolyte, Specific Heat Capacity of Electrolyte & Volume Flow Rate. We can use 1 other way(s) to calculate the same, which is/are as follows -

Boiling Point of Electrolyte = Ambient Air Temperature+Heat Absorption of Electrolyte/(Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte)

Home

FREE PDFs

🔍 Search