Density of Electrolyte Calculator

✖Electric current is the rate of flow of electric charge through a circuit, measured in amperes.ⓘ Electric Current [I]			+10% -10%
✖Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.ⓘ Resistance of Gap Between Work and Tool [R]			+10% -10%
✖Volume Flow Rate is the volume of fluid that passes per unit of time.ⓘ Volume Flow Rate [q]			+10% -10%
✖Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.ⓘ Specific Heat Capacity of Electrolyte [c_e]			+10% -10%
✖Boiling Point of electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.ⓘ Boiling Point of Electrolyte [θ_B]			+10% -10%
✖Ambient Air Temperature is the temperature where the ramming process starts.ⓘ Ambient Air Temperature [θ_o]			+10% -10%

✖The Density of Electrolyte shows the denseness of that electrolyte in a specific given area. This is taken as mass per unit volume of a given object.ⓘ Density of Electrolyte [ρ_e]

⎘ Copy

👎

Formula

✖

Density of Electrolyte

Formula

`"ρ"_{"e"} = ("I"^2*"R")/("q"*"c"_{"e"}*("θ"_{"B"}-"θ"_{"o"}))`

Example

`"997.0001kg/m³"=(("1000A")^2*"0.012Ω")/("47990.86mm³/s"*"4.18kJ/kg*K"*("368.15K"-"308.15K"))`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF

Density of Electrolyte Solution

STEP 0: Pre-Calculation Summary

Formula Used

Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))
ρ_e = (I^2*R)/(q*c_e*(θ_B-θ_o))
This formula uses 7 Variables

Variables Used

Density of Electrolyte - (Measured in Kilogram per Cubic Meter) - The Density of Electrolyte shows the denseness of that electrolyte in a specific given area. This is taken as mass per unit volume of a given object.
Electric Current - (Measured in Ampere) - Electric current is the rate of flow of electric charge through a circuit, measured in amperes.
Resistance of Gap Between Work and Tool - (Measured in Ohm) - Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.
Volume Flow Rate - (Measured in Cubic Meter per Second) - Volume Flow Rate is the volume of fluid that passes per unit of time.
Specific Heat Capacity of Electrolyte - (Measured in Joule per Kilogram per K) - Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount.
Boiling Point of Electrolyte - (Measured in Kelvin) - Boiling Point of electrolyte is the temperature at which a liquid starts to boil and transforms to vapor.
Ambient Air Temperature - (Measured in Kelvin) - Ambient Air Temperature is the temperature where the ramming process starts.

STEP 1: Convert Input(s) to Base Unit

Electric Current: 1000 Ampere --> 1000 Ampere No Conversion Required
Resistance of Gap Between Work and Tool: 0.012 Ohm --> 0.012 Ohm No Conversion Required
Volume Flow Rate: 47990.86 Cubic Millimeter per Second --> 4.799086E-05 Cubic Meter per Second (Check conversion here)
Specific Heat Capacity of Electrolyte: 4.18 Kilojoule per Kilogram per K --> 4180 Joule per Kilogram per K (Check conversion here)
Boiling Point of Electrolyte: 368.15 Kelvin --> 368.15 Kelvin No Conversion Required
Ambient Air Temperature: 308.15 Kelvin --> 308.15 Kelvin No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

ρ_e = (I^2*R)/(q*c_e*(θ_B-θ_o)) --> (1000^2*0.012)/(4.799086E-05*4180*(368.15-308.15))

Evaluating ... ...

ρ_e = 997.000052763237

STEP 3: Convert Result to Output's Unit

997.000052763237 Kilogram per Cubic Meter --> No Conversion Required

FINAL ANSWER

997.000052763237 ≈ 997.0001 Kilogram per Cubic Meter <-- Density of Electrolyte

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Gap Resistance » Density of Electrolyte

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< 14 Gap Resistance Calculators

Flow Rate of Electrolytes from Gap Resistance ECM

Go Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Density of Electrolyte

Go Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Gap Resistance from Electrolyte Flow Rate

Go Resistance of Gap Between Work and Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2

Specific Resistivity of Electrolyte given Gap between Tool and Work Surface

Go Specific Resistance of The Electrolyte = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Gap Between Tool and Work Surface*Work Piece Density*Feed Speed)

Density of Work Material given Gap between Tool and Work Surface

Go Work Piece Density = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Feed Speed*Gap Between Tool and Work Surface)

Tool Feed Speed given Gap between Tool and Work Surface

Go Feed Speed = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Gap Between Tool and Work Surface)

Supply Voltage given Gap between Tool and Work Surface

Go Supply Voltage = Gap Between Tool and Work Surface*Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed/(Current Efficiency in Decimal*Electrochemical Equivalent)

Gap between Tool and Work Surface

Go Gap Between Tool and Work Surface = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed)

Specific Resistivity of Electrolyte given Supply Current

Go Specific Resistance of The Electrolyte = Area of Penetration*Supply Voltage/(Gap Between Tool and Work Surface*Electric Current)

Gap between Tool and Work Surface given Supply Current

Go Gap Between Tool and Work Surface = Area of Penetration*Supply Voltage/(Specific Resistance of The Electrolyte*Electric Current)

Gap Resistance between Work and Tool

Go Resistance of Gap Between Work and Tool = (Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface)/Cross Sectional Area of Gap

Specific Resistance of Electrolyte

Go Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface

Cross-Sectional Area of Gap

Go Cross Sectional Area of Gap = (Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface)/Resistance of Gap Between Work and Tool

Width of Equilibrium Gap

Go Gap Between Tool and Work Surface = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Specific Resistance of The Electrolyte

Density of Electrolyte Formula

What is Faraday's I law of electrolysis ?

The first law of Faraday’s electrolysis states that the chemical change produced during electrolysis is proportional to the current passed and the electrochemical equivalence of the anode material.

How to Calculate Density of Electrolyte?

Density of Electrolyte calculator uses Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)) to calculate the Density of Electrolyte, The Density of electrolyte formula is defined as the ratio of mass per unit volume of the given electrolyte. Density of Electrolyte is denoted by ρ_e symbol.

How to calculate Density of Electrolyte using this online calculator? To use this online calculator for Density of Electrolyte, enter Electric Current (I), Resistance of Gap Between Work and Tool (R), Volume Flow Rate (q), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B) & Ambient Air Temperature (θ_o) and hit the calculate button. Here is how the Density of Electrolyte calculation can be explained with given input values -> 998891.2 = (1000^2*0.012)/(4.799086E-05*4180*(368.15-308.15)).

FAQ

What is Density of Electrolyte?

The Density of electrolyte formula is defined as the ratio of mass per unit volume of the given electrolyte and is represented as ρ_e = (I^2*R)/(q*c_e*(θ_B-θ_o)) or Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)). Electric current is the rate of flow of electric charge through a circuit, measured in amperes, Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry, Volume Flow Rate is the volume of fluid that passes per unit of time, Specific Heat Capacity of electrolyte is the heat required to raise the temperature of the unit mass of a given substance by a given amount, Boiling Point of electrolyte is the temperature at which a liquid starts to boil and transforms to vapor & Ambient Air Temperature is the temperature where the ramming process starts.

How to calculate Density of Electrolyte?

The Density of electrolyte formula is defined as the ratio of mass per unit volume of the given electrolyte is calculated using Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)). To calculate Density of Electrolyte, you need Electric Current (I), Resistance of Gap Between Work and Tool (R), Volume Flow Rate (q), Specific Heat Capacity of Electrolyte (c_e), Boiling Point of Electrolyte (θ_B) & Ambient Air Temperature (θ_o). With our tool, you need to enter the respective value for Electric Current, Resistance of Gap Between Work and Tool, Volume Flow Rate, Specific Heat Capacity of Electrolyte, Boiling Point of Electrolyte & Ambient Air Temperature and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search