Discharge for Partially Penetrating Well given Correction Factor Solution

STEP 0: Pre-Calculation Summary
Formula Used
Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin.
Qv = G*Qee
This formula uses 3 Variables
Variables Used
Discharge for Partially Penetrating Well - (Measured in Cubic Meter per Second) - Discharge for Partially Penetrating Well is in terms of volumetric flow rate.
Correction Factor - Correction Factor is a factor that is applied for the correction in the Partial Penetration.
Discharge in Enviro. Engin. - (Measured in Cubic Meter per Second) - Discharge in Enviro. Engin. is the rate of flow of a liquid.
STEP 1: Convert Input(s) to Base Unit
Correction Factor: 5.6 --> No Conversion Required
Discharge in Enviro. Engin.: 0.0005 Cubic Meter per Second --> 0.0005 Cubic Meter per Second No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
Qv = G*Qee --> 5.6*0.0005
Evaluating ... ...
Qv = 0.0028
STEP 3: Convert Result to Output's Unit
0.0028 Cubic Meter per Second --> No Conversion Required
FINAL ANSWER
0.0028 Cubic Meter per Second <-- Discharge for Partially Penetrating Well
(Calculation completed in 00.004 seconds)

Credits

Created by Suraj Kumar
Birsa Institute of Technology (BIT), Sindri
Suraj Kumar has created this Calculator and 2200+ more calculators!
Verified by Ishita Goyal
Meerut Institute of Engineering and Technology (MIET), Meerut
Ishita Goyal has verified this Calculator and 2600+ more calculators!

11 Partially Penetrating Artesian Well Calculators

Thickness of Aquifer given Discharge for Partially Penetrating Well
Go Initial Aquifer Thickness = Depth of Water+(Discharge for Partially Penetrating Well*(log((Radius of Influence/Radius of Well in Eviron. Engin.),e)))/(2*pi*Coefficient of Permeability in Environ. Engin.*Aquifer Thickness During Pumping*Correction Factor)
Correction Factor for Partial Penetration given Discharge for Partially Penetrating Well
Go Correction Factor = Discharge for Partially Penetrating Well/((2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water))/(log((Radius of Influence/Radius of Well in Eviron. Engin.),e)))
Coefficient of Permeability given Discharge for Partially Penetrating Well
Go Coefficient of Permeability = Discharge for Partially Penetrating Well/((2*pi*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/(log((Radius of Influence/Radius of Well in Eviron. Engin.),e)))
Depth of Water in Well given Discharge for Partially Penetrating Well
Go Depth of Water = Initial Aquifer Thickness-((Discharge for Partially Penetrating Well*(log((Radius of Influence/Radius of Well in Eviron. Engin.),e)))/(2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*Correction Factor))
Aquifer Thickness given Discharge for Partially Penetrating Well
Go Aquifer Thickness During Pumping = Discharge for Partially Penetrating Well/((2*pi*Coefficient of Permeability*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/(log((Radius of Influence/Radius of Well in Eviron. Engin.),e)))
Discharge for Partially Penetrating Well
Go Discharge for Partially Penetrating Well = (2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/(log((Radius of Influence/Radius of Well in Eviron. Engin.),e))
Radius of Influence given Discharge for Partially Penetrating Well
Go Radius of Influence in Eviron. Engin. = (Radius of Well in Eviron. Engin.*exp((2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/Discharge at Time t=0))
Radius of Well given Discharge for Partially Penetrating Well
Go Radius of Well in Eviron. Engin. = Radius of Influence in Eviron. Engin./(exp((2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/Discharge))
Correction Factor for Partial Penetration given Discharge for Fully Penetrating Well
Go Correction Factor = Discharge for Partially Penetrating Well/Discharge in Enviro. Engin.
Discharge for Partially Penetrating Well given Correction Factor
Go Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin.
Discharge for Fully Penetrating Well given Correction Factor
Go Discharge in Enviro. Engin. = Discharge for Partially Penetrating Well/Correction Factor

Discharge for Partially Penetrating Well given Correction Factor Formula

Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin.
Qv = G*Qee

What is Discharge?

The amount of fluid passing a section of a stream in unit time is called the discharge. If v is the mean velocity and A is the cross sectional area, the discharge Q is defined by Q = Av which is known as volume flow rate.

How to Calculate Discharge for Partially Penetrating Well given Correction Factor?

Discharge for Partially Penetrating Well given Correction Factor calculator uses Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin. to calculate the Discharge for Partially Penetrating Well, The Discharge for Partially Penetrating Well given Correction Factor is defined as the value of discharge when we have prior information of other parameters used. Discharge for Partially Penetrating Well is denoted by Qv symbol.

How to calculate Discharge for Partially Penetrating Well given Correction Factor using this online calculator? To use this online calculator for Discharge for Partially Penetrating Well given Correction Factor, enter Correction Factor (G) & Discharge in Enviro. Engin. (Qee) and hit the calculate button. Here is how the Discharge for Partially Penetrating Well given Correction Factor calculation can be explained with given input values -> 0.0028 = 5.6*0.0005.

FAQ

What is Discharge for Partially Penetrating Well given Correction Factor?
The Discharge for Partially Penetrating Well given Correction Factor is defined as the value of discharge when we have prior information of other parameters used and is represented as Qv = G*Qee or Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin.. Correction Factor is a factor that is applied for the correction in the Partial Penetration & Discharge in Enviro. Engin. is the rate of flow of a liquid.
How to calculate Discharge for Partially Penetrating Well given Correction Factor?
The Discharge for Partially Penetrating Well given Correction Factor is defined as the value of discharge when we have prior information of other parameters used is calculated using Discharge for Partially Penetrating Well = Correction Factor*Discharge in Enviro. Engin.. To calculate Discharge for Partially Penetrating Well given Correction Factor, you need Correction Factor (G) & Discharge in Enviro. Engin. (Qee). With our tool, you need to enter the respective value for Correction Factor & Discharge in Enviro. Engin and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Discharge for Partially Penetrating Well?
In this formula, Discharge for Partially Penetrating Well uses Correction Factor & Discharge in Enviro. Engin. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Discharge for Partially Penetrating Well = (2*pi*Coefficient of Permeability*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water)*Correction Factor)/(log((Radius of Influence/Radius of Well in Eviron. Engin.),e))
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!