Feed given Taylor's Tool Life, Cutting Velocity, and Intercept Solution

STEP 0: Pre-Calculation Summary
Formula Used
Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate)
f = (C/(V*(dcut^b)*(T^n)))^(1/a)
This formula uses 8 Variables
Variables Used
Feed Rate - (Measured in Meter Per Revolution) - Feed Rate is defined as the tool's distance travelled during one spindle revolution.
Taylor's Intercept or Taylor's Constant - Taylor's Intercept or Taylor's Constant is an experimental constant that depends mainly upon the tool-work materials and the cutting environment.
Cutting Velocity - (Measured in Meter per Second) - The Cutting Velocity is the tangential velocity at the periphery of the cutter or workpiece (whichever is rotating).
Depth of Cut - (Measured in Meter) - Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.
Taylor's exponent for Depth of Cut - Taylor's exponent for Depth of Cut is an experimental exponent used to draw a relation between the depth of cut to Workpiece and Tool Life.
Tool Life - (Measured in Second) - Tool Life is the period of time for which the cutting edge, affected by the cutting procedure, retains its cutting capacity between sharpening operations.
Taylor's Tool Life Exponent - Taylor's Tool Life Exponent is an experimental exponent that helps in quantifying the rate of Tool Wear.
Taylor's exponent for Feed Rate - Taylor's exponent for Feed Rate is an experimental exponent used to draw a relation between feed rate to Workpiece and Tool Life.
STEP 1: Convert Input(s) to Base Unit
Taylor's Intercept or Taylor's Constant: 85.13059 --> No Conversion Required
Cutting Velocity: 50 Meter per Minute --> 0.833333333333333 Meter per Second (Check conversion here)
Depth of Cut: 13 Millimeter --> 0.013 Meter (Check conversion here)
Taylor's exponent for Depth of Cut: 0.24 --> No Conversion Required
Tool Life: 75 Minute --> 4500 Second (Check conversion here)
Taylor's Tool Life Exponent: 0.846625 --> No Conversion Required
Taylor's exponent for Feed Rate: 0.2 --> No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
f = (C/(V*(dcut^b)*(T^n)))^(1/a) --> (85.13059/(0.833333333333333*(0.013^0.24)*(4500^0.846625)))^(1/0.2)
Evaluating ... ...
f = 0.000699998648573685
STEP 3: Convert Result to Output's Unit
0.000699998648573685 Meter Per Revolution -->0.699998648573685 Millimeter Per Revolution (Check conversion here)
FINAL ANSWER
0.699998648573685 0.699999 Millimeter Per Revolution <-- Feed Rate
(Calculation completed in 00.020 seconds)

Credits

Created by Kumar Siddhant
Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur
Kumar Siddhant has created this Calculator and 400+ more calculators!
Verified by Parul Keshav
National Institute of Technology (NIT), Srinagar
Parul Keshav has verified this Calculator and 400+ more calculators!

7 Modified Taylor's Tool Life Equation Calculators

Taylor's Exponent of Depth of Cut
Go Taylor's exponent for Depth of Cut = ln(Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Feed Rate^Taylor's exponent for Feed Rate)*(Maximum Tool Life^Taylor's Tool Life Exponent)))/ln(Depth of Cut)
Taylor's Exponent of Feed
Go Taylor's exponent for Feed Rate = ln(Taylor's Intercept or Taylor's Constant/(Cutting Velocity*Depth of Cut^Taylor's exponent for Depth of Cut*Maximum Tool Life^Taylor's Tool Life Exponent))/ln(Feed Rate)
Taylor's Tool Life Exponent using Cutting Velocity and Taylor's Tool Life
Go Taylor's Tool Life Exponent = ln(Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Feed Rate^Taylor's exponent for Feed Rate)*(Depth of Cut^Taylor's exponent for Depth of Cut)))/ln(Tool Life)
Taylor's Tool Life given Cutting Velocity and Taylor's Intercept
Go Tool Life = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Feed Rate^Taylor's exponent for Feed Rate)*(Depth of Cut^Taylor's exponent for Depth of Cut)))^(1/Taylor's Tool Life Exponent)
Feed given Taylor's Tool Life, Cutting Velocity, and Intercept
Go Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate)
Depth of Cut for given Taylor's Tool Life, Cutting Velocity and Intercept
Go Depth of Cut = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*Feed Rate^Taylor's exponent for Feed Rate*Tool Life^Taylor's Tool Life Exponent))^(1/Taylor's exponent for Depth of Cut)
Taylor's Intercept given Cutting Velocity and Tool Life
Go Taylor's Intercept or Taylor's Constant = Cutting Velocity*(Tool Life^Taylor's Tool Life Exponent)*(Feed Rate^Taylor's exponent for Feed Rate)*(Depth of Cut^Taylor's exponent for Depth of Cut)

Feed given Taylor's Tool Life, Cutting Velocity, and Intercept Formula

Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate)
f = (C/(V*(dcut^b)*(T^n)))^(1/a)

Modified Taylor's Tool Life Equation and Effects of Feed on Tool Life.

The modified Taylor's Tool Life equation is given as:
VTnfadb=C
Tool Life varies with feed rate. At a low feed rate, the area of the chip that passes across the tool surfaces will be relatively large for a given volume cut, and relatively small for a high feed rate. From this, it seems that tool life should increase with the increase in feed rate, but as the cutting forces on tools also increase with the increase in feed rate, it leads to decreased tool life. Thus these two opposing influences of the feed rate upon tool give rise to an optimum rate of feed which is about 0.25 to 0.50 mm/rev.

How to Calculate Feed given Taylor's Tool Life, Cutting Velocity, and Intercept?

Feed given Taylor's Tool Life, Cutting Velocity, and Intercept calculator uses Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate) to calculate the Feed Rate, The Feed given Taylor's Tool Life, Cutting Velocity, and Intercept is a method to determine the maximum Feed that can be applied on the Workpiece to get a specified Tool Life under a given Cutting Velocity. Feed Rate is denoted by f symbol.

How to calculate Feed given Taylor's Tool Life, Cutting Velocity, and Intercept using this online calculator? To use this online calculator for Feed given Taylor's Tool Life, Cutting Velocity, and Intercept, enter Taylor's Intercept or Taylor's Constant (C), Cutting Velocity (V), Depth of Cut (dcut), Taylor's exponent for Depth of Cut (b), Tool Life (T), Taylor's Tool Life Exponent (n) & Taylor's exponent for Feed Rate (a) and hit the calculate button. Here is how the Feed given Taylor's Tool Life, Cutting Velocity, and Intercept calculation can be explained with given input values -> 699.9999 = (85.13059/(0.833333333333333*(0.013^0.24)*(4500^0.846625)))^(1/0.2).

FAQ

What is Feed given Taylor's Tool Life, Cutting Velocity, and Intercept?
The Feed given Taylor's Tool Life, Cutting Velocity, and Intercept is a method to determine the maximum Feed that can be applied on the Workpiece to get a specified Tool Life under a given Cutting Velocity and is represented as f = (C/(V*(dcut^b)*(T^n)))^(1/a) or Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate). Taylor's Intercept or Taylor's Constant is an experimental constant that depends mainly upon the tool-work materials and the cutting environment, The Cutting Velocity is the tangential velocity at the periphery of the cutter or workpiece (whichever is rotating), Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction, Taylor's exponent for Depth of Cut is an experimental exponent used to draw a relation between the depth of cut to Workpiece and Tool Life, Tool Life is the period of time for which the cutting edge, affected by the cutting procedure, retains its cutting capacity between sharpening operations, Taylor's Tool Life Exponent is an experimental exponent that helps in quantifying the rate of Tool Wear & Taylor's exponent for Feed Rate is an experimental exponent used to draw a relation between feed rate to Workpiece and Tool Life.
How to calculate Feed given Taylor's Tool Life, Cutting Velocity, and Intercept?
The Feed given Taylor's Tool Life, Cutting Velocity, and Intercept is a method to determine the maximum Feed that can be applied on the Workpiece to get a specified Tool Life under a given Cutting Velocity is calculated using Feed Rate = (Taylor's Intercept or Taylor's Constant/(Cutting Velocity*(Depth of Cut^Taylor's exponent for Depth of Cut)*(Tool Life^Taylor's Tool Life Exponent)))^(1/Taylor's exponent for Feed Rate). To calculate Feed given Taylor's Tool Life, Cutting Velocity, and Intercept, you need Taylor's Intercept or Taylor's Constant (C), Cutting Velocity (V), Depth of Cut (dcut), Taylor's exponent for Depth of Cut (b), Tool Life (T), Taylor's Tool Life Exponent (n) & Taylor's exponent for Feed Rate (a). With our tool, you need to enter the respective value for Taylor's Intercept or Taylor's Constant, Cutting Velocity, Depth of Cut, Taylor's exponent for Depth of Cut, Tool Life, Taylor's Tool Life Exponent & Taylor's exponent for Feed Rate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!