Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String Calculator

✖Vertical Force at Bottom end of Drill String depends on the density of drilling mud, cross section area of steel in the pipe and length of pipe hanging in the well.ⓘ Vertical Force at Bottom end of Drill String [f_z]			+10% -10%
✖Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.ⓘ Density of Drilling Mud [ρ_m]			+10% -10%
✖Cross Section Area of Steel in Pipe is the extent of a surface or plane figure as measured in square units.ⓘ Cross Section Area of Steel in Pipe [A_s]			+10% -10%

✖Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.ⓘ Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String [L]

⎘ Copy

👎

Formula

✖

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String

Formula

`"L" = "f"_{"z"}/("ρ"_{"m"}*"[g]"*"A"_{"s"})`

Example

`"15.99952m"="146.86kN"/("1440kg/m³"*"[g]"*"0.65m²")`

Calculator

LaTeX

Reset

👍

Download Hydrostatics Formulas PDF

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String Solution

STEP 0: Pre-Calculation Summary

Formula Used

Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe)
L = f_z/(ρ_m*[g]*A_s)
This formula uses 1 Constants, 4 Variables

Constants Used

[g] - Gravitational acceleration on Earth Value Taken As 9.80665

Variables Used

Length of Pipe Hanging in Well - (Measured in Meter) - Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.
Vertical Force at Bottom end of Drill String - (Measured in Newton) - Vertical Force at Bottom end of Drill String depends on the density of drilling mud, cross section area of steel in the pipe and length of pipe hanging in the well.
Density of Drilling Mud - (Measured in Kilogram per Cubic Meter) - Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.
Cross Section Area of Steel in Pipe - (Measured in Square Meter) - Cross Section Area of Steel in Pipe is the extent of a surface or plane figure as measured in square units.

STEP 1: Convert Input(s) to Base Unit

Vertical Force at Bottom end of Drill String: 146.86 Kilonewton --> 146860 Newton (Check conversion here)
Density of Drilling Mud: 1440 Kilogram per Cubic Meter --> 1440 Kilogram per Cubic Meter No Conversion Required
Cross Section Area of Steel in Pipe: 0.65 Square Meter --> 0.65 Square Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

L = f_z/(ρ_m*[g]*A_s) --> 146860/(1440*[g]*0.65)

Evaluating ... ...

L = 15.9995216920875

STEP 3: Convert Result to Output's Unit

15.9995216920875 Meter --> No Conversion Required

FINAL ANSWER

15.9995216920875 ≈ 15.99952 Meter <-- Length of Pipe Hanging in Well

(Calculation completed in 00.007 seconds)

You are here -

Home » Engineering » Civil » Coastal and Ocean Engineering » Offshore Hydromechanics » Hydrostatics » Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by M Naveen

National Institute of Technology (NIT), Warangal

M Naveen has verified this Calculator and 900+ more calculators!

< 18 Hydrostatics Calculators

Mass Density of Drilling Mud when Buoyant Force acts in Direction opposite to Gravity Force

Go Density of Drilling Mud = -((Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))-Mass Density of Steel))

Length of Pipe Hanging in Well given Effective Tension

Go Length of Pipe Hanging in Well = ((Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)+Coordinate measured Downward from Top))

Coordinate measured Downward from Top given Effective Tension

Go Coordinate measured Downward from Top = -(Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)-Length of Pipe Hanging in Well)

Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force

Go Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)

Cross Section Area of Steel given Effective Tension

Go Cross Section Area of Steel in Pipe = Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Effective Tension given Buoyant Force acts in Direction opposite to Gravity Force

Go Effective Tension = (Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)

Coordinate measured Downward from Top given Tension on Vertical Drill String

Go Coordinate measured Downward from Top = -((Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))-Length of Pipe Hanging in Well)

Cross Section Area of Steel in Pipe given Tension on Vertical Drill String

Go Cross Section Area of Steel in Pipe = Tension on Vertical Drill String/(Mass Density of Steel*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Length of Pipe Hanging in Well given Tension on Vertical Drill String

Go Length of Pipe Hanging in Well = (Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))+Coordinate measured Downward from Top

Mass Density of Steel for Tension on Vertical Drill String

Go Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Tension on Vertical Drill String

Go Tension on Vertical Drill String = Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String

Go Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe)

Mass Density of Drilling Mud given Vertical Force at Bottom End of Drill String

Go Density of Drilling Mud = Vertical Force at Bottom end of Drill String/([g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well)

Vertical Force at Bottom End of Drill String

Go Vertical Force at Bottom end of Drill String = Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well

Mass Density of Drilling Mud for Lower Section of Drill String Length in Compression

Go Density of Drilling Mud = (Lower Section of Drill String Length*Mass Density of Steel)/Length of Pipe Hanging in Well

Length of Pipe Hanging given Lower Section of Drill String Length in Compression

Go Length of Pipe Hanging in Well = (Lower Section of Drill String Length*Mass Density of Steel)/Density of Drilling Mud

Mass Density of Steel for Lower Section of Drill String Length in Compression

Go Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length

Lower Section of Drill String Length that is in Compression

Go Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String Formula

Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe)
L = f_z/(ρ_m*[g]*A_s)

What is Buoyancy?

Buoyancy is the force that causes objects to float. It is the force exerted on an object that is partly or wholly immersed in a fluid. Buoyancy is caused by the differences in pressure acting on opposite sides of an object immersed in a static fluid. It is also known as the buoyant force.

How to Calculate Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String?

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String calculator uses Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe) to calculate the Length of Pipe Hanging in Well, Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String when pressures on (vertical) drill string walls are in equilibrium and contribute no vertical force. drill string does experience vertical force at its bottom end. Length of Pipe Hanging in Well is denoted by L symbol.

How to calculate Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String using this online calculator? To use this online calculator for Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String, enter Vertical Force at Bottom end of Drill String (f_z), Density of Drilling Mud (ρ_m) & Cross Section Area of Steel in Pipe (A_s) and hit the calculate button. Here is how the Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String calculation can be explained with given input values -> 15.99952 = 146860/(1440*[g]*0.65).

FAQ

What is Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String?

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String when pressures on (vertical) drill string walls are in equilibrium and contribute no vertical force. drill string does experience vertical force at its bottom end and is represented as L = f_z/(ρ_m*[g]*A_s) or Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe). Vertical Force at Bottom end of Drill String depends on the density of drilling mud, cross section area of steel in the pipe and length of pipe hanging in the well, Density of Drilling Mud considering a steel drilling pipe hanging in an oil well & Cross Section Area of Steel in Pipe is the extent of a surface or plane figure as measured in square units.

How to calculate Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String?

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String when pressures on (vertical) drill string walls are in equilibrium and contribute no vertical force. drill string does experience vertical force at its bottom end is calculated using Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe). To calculate Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String, you need Vertical Force at Bottom end of Drill String (f_z), Density of Drilling Mud (ρ_m) & Cross Section Area of Steel in Pipe (A_s). With our tool, you need to enter the respective value for Vertical Force at Bottom end of Drill String, Density of Drilling Mud & Cross Section Area of Steel in Pipe and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Length of Pipe Hanging in Well?

In this formula, Length of Pipe Hanging in Well uses Vertical Force at Bottom end of Drill String, Density of Drilling Mud & Cross Section Area of Steel in Pipe. We can use 3 other way(s) to calculate the same, which is/are as follows -

Length of Pipe Hanging in Well = (Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))+Coordinate measured Downward from Top
Length of Pipe Hanging in Well = ((Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)+Coordinate measured Downward from Top))
Length of Pipe Hanging in Well = (Lower Section of Drill String Length*Mass Density of Steel)/Density of Drilling Mud

Home

FREE PDFs

🔍 Search