Noise Figure of Double Side Band Calculator

✖Diode temperature is the measure of heat to flow in the diode preferentially in one direction.ⓘ Diode Temperature [T_d]			+10% -10%
✖Diode Resistance can be defined as the effective opposition offered by the diode to the flow of current through it.ⓘ Diode Resistance [R_d]			+10% -10%
✖Output Resistance of Signal Generator is a key operating parameter that controls the current generation signal generator when used as a power source.ⓘ Output Resistance of Signal Generator [R_g]			+10% -10%
✖Ambient Temperature is the temperature of the surrounding.ⓘ Ambient Temperature [T₀]			+10% -10%

✖Noise Figure Of double side band in decibels (dB) between the noise output of the actual receiver to the noise output of an “ideal” receiver with the same overall gain and bandwidth.ⓘ Noise Figure of Double Side Band [F_dsb]

⎘ Copy

👎

Formula

✖

Noise Figure of Double Side Band

Formula

`"F"_{"dsb"} = 1+(("T"_{"d"}*"R"_{"d"})/("R"_{"g"}*"T"_{"0"}))`

Example

`"7.151515dB"=1+(("290K"*"210Ω")/("33Ω"*"300K"))`

Calculator

LaTeX

Reset

👍

Download Non Linear Circuits Formulas PDF PDF Image

Noise Figure of Double Side Band Solution

STEP 0: Pre-Calculation Summary

Formula Used

Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))
F_dsb = 1+((T_d*R_d)/(R_g*T₀))
This formula uses 5 Variables

Variables Used

Noise Figure of Double Side Band - (Measured in Decibel) - Noise Figure Of double side band in decibels (dB) between the noise output of the actual receiver to the noise output of an “ideal” receiver with the same overall gain and bandwidth.
Diode Temperature - (Measured in Kelvin) - Diode temperature is the measure of heat to flow in the diode preferentially in one direction.
Diode Resistance - (Measured in Ohm) - Diode Resistance can be defined as the effective opposition offered by the diode to the flow of current through it.
Output Resistance of Signal Generator - (Measured in Ohm) - Output Resistance of Signal Generator is a key operating parameter that controls the current generation signal generator when used as a power source.
Ambient Temperature - (Measured in Kelvin) - Ambient Temperature is the temperature of the surrounding.

STEP 1: Convert Input(s) to Base Unit

Diode Temperature: 290 Kelvin --> 290 Kelvin No Conversion Required
Diode Resistance: 210 Ohm --> 210 Ohm No Conversion Required
Output Resistance of Signal Generator: 33 Ohm --> 33 Ohm No Conversion Required
Ambient Temperature: 300 Kelvin --> 300 Kelvin No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

F_dsb = 1+((T_d*R_d)/(R_g*T₀)) --> 1+((290*210)/(33*300))

Evaluating ... ...

F_dsb = 7.15151515151515

STEP 3: Convert Result to Output's Unit

7.15151515151515 Decibel --> No Conversion Required

FINAL ANSWER

7.15151515151515 ≈ 7.151515 Decibel <-- Noise Figure of Double Side Band

(Calculation completed in 00.020 seconds)

You are here -

Home » Engineering » Electronics » Microwave Theory » Microwave Semiconductor Devices » Non Linear Circuits » Noise Figure of Double Side Band

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< 16 Non Linear Circuits Calculators

Room Temperature

Go Ambient Temperature = (2*Diode Temperature*((1/(Coupling Coefficient*Q Factor))+(1/((Coupling Coefficient*Q Factor)^2))))/(Noise Figure of Up-Converter-1)

Average Diode Temperature using Single Side Band Noise

Go Diode Temperature = (Noise Figure of Single Side Band-2)*((Output Resistance of Signal Generator*Ambient Temperature)/(2*Diode Resistance))

Noise Figure of Single Side Band

Go Noise Figure of Single Side Band = 2+((2*Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))

Noise Figure of Double Side Band

Go Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))

Voltage Reflection Coefficient of Tunnel Diode

Go Voltage Reflection Coefficient = (Impedance Tunnel Diode-Characteristic Impedance)/(Impedance Tunnel Diode+Characteristic Impedance)

Amplifier Gain of Tunnel Diode

Go Amplifier Gain of Tunnel Diode = Negative Resistance in Tunnel Diode/(Negative Resistance in Tunnel Diode-Load Resistance)

Ratio Negative Resistance to Series Resistance

Go Ratio Negative Resistance to Series Resistance = Equivalent Negative Resistance/Total Series Resistance at Idler Frequency

Tunnel Diode Output Power

Go Output Power of Tunnel Diode = (Voltage Tunnel Diode*Current Tunnel Diode)/(2*pi)

Bandwidth using Dynamic Quality Factor

Go Bandwidth = Dynamic Q-Factor/(Angular Frequency*Series Resistance of Diode)

Dynamic Q Factor

Go Dynamic Q-Factor = Bandwidth/(Angular Frequency*Series Resistance of Diode)

Maximum Applied Current across Diode

Go Maximum Applied Current = Maximum Applied Voltage/Reactive Impedence

Reactive Impedence

Go Reactive Impedence = Maximum Applied Voltage/Maximum Applied Current

Maximum Applied Voltage across Diode

Go Maximum Applied Voltage = Maximum Electric Field*Depletion Length

Negative Conductance of Tunnel Diode

Go Negative Conductance Tunnel Diode = 1/(Negative Resistance in Tunnel Diode)

Magnitude of Negative Resistance

Go Negative Resistance in Tunnel Diode = 1/(Negative Conductance Tunnel Diode)

Power Gain of Tunnel Diode

Go Power Gain of Tunnel Diode = Voltage Reflection Coefficient^2

Noise Figure of Double Side Band Formula

Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature))
F_dsb = 1+((T_d*R_d)/(R_g*T₀))

What Is Homo- Junction Transistor?

When the transistor junction is joined by two similar materials such as silicon- to silicon or germanium-to-germanium, it is called a homo junction transistor.

How to Calculate Noise Figure of Double Side Band?

Noise Figure of Double Side Band calculator uses Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature)) to calculate the Noise Figure of Double Side Band, The Noise Figure of Double Side Band formula is defined as is the maximum voltage amplitude of extraneous signal that can be algebraically added to the noise-free worst-case input level without causing the output voltage to deviate from the allowable logic voltage level produced inside a Double Side Band. Noise Figure of Double Side Band is denoted by F_dsb symbol.

How to calculate Noise Figure of Double Side Band using this online calculator? To use this online calculator for Noise Figure of Double Side Band, enter Diode Temperature (T_d), Diode Resistance (R_d), Output Resistance of Signal Generator (R_g) & Ambient Temperature (T₀) and hit the calculate button. Here is how the Noise Figure of Double Side Band calculation can be explained with given input values -> 7.151515 = 1+((290*210)/(33*300)).

FAQ

What is Noise Figure of Double Side Band?

The Noise Figure of Double Side Band formula is defined as is the maximum voltage amplitude of extraneous signal that can be algebraically added to the noise-free worst-case input level without causing the output voltage to deviate from the allowable logic voltage level produced inside a Double Side Band and is represented as F_dsb = 1+((T_d*R_d)/(R_g*T₀)) or Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature)). Diode temperature is the measure of heat to flow in the diode preferentially in one direction, Diode Resistance can be defined as the effective opposition offered by the diode to the flow of current through it, Output Resistance of Signal Generator is a key operating parameter that controls the current generation signal generator when used as a power source & Ambient Temperature is the temperature of the surrounding.

How to calculate Noise Figure of Double Side Band?

The Noise Figure of Double Side Band formula is defined as is the maximum voltage amplitude of extraneous signal that can be algebraically added to the noise-free worst-case input level without causing the output voltage to deviate from the allowable logic voltage level produced inside a Double Side Band is calculated using Noise Figure of Double Side Band = 1+((Diode Temperature*Diode Resistance)/(Output Resistance of Signal Generator*Ambient Temperature)). To calculate Noise Figure of Double Side Band, you need Diode Temperature (T_d), Diode Resistance (R_d), Output Resistance of Signal Generator (R_g) & Ambient Temperature (T₀). With our tool, you need to enter the respective value for Diode Temperature, Diode Resistance, Output Resistance of Signal Generator & Ambient Temperature and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search