Radius of electrode from pressure flushing hole Calculator

✖Radial location of pressure is the radial location of pressure during EDM.ⓘ Radial Location of Pressure [r]			+10% -10%
✖Pressure in Flushing Hole is the pressure in hole during EDM machining.ⓘ Pressure in Flushing Hole [P₁]			+10% -10%
✖Atmospheric pressure, also known as barometric pressure, is the pressure within the atmosphere of Earth.ⓘ Atmospheric Pressure [P_atm]			+10% -10%
✖Pressure in the flushing gap is the pressure at any distance r in fluid flow passage through the electrode in the EDM process.ⓘ Pressure in the Flushing Gap [P_r]			+10% -10%
✖Radius of flushing hole is the radius of flushing hole in EDM.ⓘ Radius of Flushing Hole [R₁]			+10% -10%

✖Radius of the electrodes is defined as the radius of the electrode used for unconventional machining by EDM.ⓘ Radius of electrode from pressure flushing hole [R₀]

⎘ Copy

👎

Formula

✖

Radius of electrode from pressure flushing hole

Formula

`"R"_{"0"} = (("r")^(("P"_{"1"}-"P"_{"atm"})/("P"_{"r"}-"P"_{"atm"}))/"R"_{"1"})^(("P"_{"r"}-"P"_{"atm"})/("P"_{"1"}-"P"_{"r"}))`

Example

`"2.069957cm"=(("2.6cm")^(("11N/cm²"-"10.1325N/cm²")/("4.38N/cm²"-"10.1325N/cm²"))/"2cm")^(("4.38N/cm²"-"10.1325N/cm²")/("11N/cm²"-"4.38N/cm²"))`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF

Radius of electrode from pressure flushing hole Solution

STEP 0: Pre-Calculation Summary

Formula Used

Radius of the Electrodes = ((Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure))/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Pressure in the Flushing Gap))
R₀ = ((r)^((P₁-P_atm)/(P_r-P_atm))/R₁)^((P_r-P_atm)/(P₁-P_r))
This formula uses 6 Variables

Variables Used

Radius of the Electrodes - (Measured in Meter) - Radius of the electrodes is defined as the radius of the electrode used for unconventional machining by EDM.
Radial Location of Pressure - (Measured in Meter) - Radial location of pressure is the radial location of pressure during EDM.
Pressure in Flushing Hole - (Measured in Pascal) - Pressure in Flushing Hole is the pressure in hole during EDM machining.
Atmospheric Pressure - (Measured in Pascal) - Atmospheric pressure, also known as barometric pressure, is the pressure within the atmosphere of Earth.
Pressure in the Flushing Gap - (Measured in Pascal) - Pressure in the flushing gap is the pressure at any distance r in fluid flow passage through the electrode in the EDM process.
Radius of Flushing Hole - (Measured in Meter) - Radius of flushing hole is the radius of flushing hole in EDM.

STEP 1: Convert Input(s) to Base Unit

Radial Location of Pressure: 2.6 Centimeter --> 0.026 Meter (Check conversion here)
Pressure in Flushing Hole: 11 Newton per Square Centimeter --> 110000 Pascal (Check conversion here)
Atmospheric Pressure: 10.1325 Newton per Square Centimeter --> 101325 Pascal (Check conversion here)
Pressure in the Flushing Gap: 4.38 Newton per Square Centimeter --> 43800 Pascal (Check conversion here)
Radius of Flushing Hole: 2 Centimeter --> 0.02 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R₀ = ((r)^((P₁-P_atm)/(P_r-P_atm))/R₁)^((P_r-P_atm)/(P₁-P_r)) --> ((0.026)^((110000-101325)/(43800-101325))/0.02)^((43800-101325)/(110000-43800))

Evaluating ... ...

R₀ = 0.0206995733547482

STEP 3: Convert Result to Output's Unit

0.0206995733547482 Meter -->2.06995733547482 Centimeter (Check conversion here)

FINAL ANSWER

2.06995733547482 ≈ 2.069957 Centimeter <-- Radius of the Electrodes

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Pressure distribution in the flushing gap » Radius of electrode from pressure flushing hole

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Sai Venkata Phanindra Chary Arendra

Vallurupalli Nageswara Rao Vignana Jyothi Institute of Engineering and Technology (VNRVJIET), Hyderabad

Sai Venkata Phanindra Chary Arendra has verified this Calculator and 300+ more calculators!

< 6 Pressure distribution in the flushing gap Calculators

Radius of electrode from pressure flushing hole

Go Radius of the Electrodes = ((Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure))/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Pressure in the Flushing Gap))

Atmospheric pressure at electrode tip

Go Atmospheric Pressure = (Pressure in the Flushing Gap*ln(Radius of the Electrodes/Radius of Flushing Hole)-Pressure in Flushing Hole*ln(Radius of the Electrodes/Radial Location of Pressure))/(ln(Radial Location of Pressure/Radius of Flushing Hole))

Pressure distribution in flushing gap

Go Pressure in the Flushing Gap = Atmospheric Pressure+((Pressure in Flushing Hole-Atmospheric Pressure)*ln(Radius of the Electrodes/Radial Location of Pressure))/(ln(Radius of the Electrodes/Radius of Flushing Hole))

Pressure in flushing hole

Go Pressure in Flushing Hole = Atmospheric Pressure+(Pressure in the Flushing Gap-Atmospheric Pressure)*(ln(Radius of the Electrodes/Radius of Flushing Hole)/ln(Radius of the Electrodes/Radial Location of Pressure))

Radial location of pressure distribution

Go Radial Location of Pressure = Radius of the Electrodes/((Radius of the Electrodes/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Atmospheric Pressure)))

Radius of flushing hole EDM

Go Radius of Flushing Hole = Radius of the Electrodes/((Radius of the Electrodes/Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure)))

Radius of electrode from pressure flushing hole Formula

What is term Flushing means in Electric Discharge Machining ?

Flushing refers to the method in which the dielectric fluid flows between the tool and the work gap.The efficiency of machining depends to a greater extent on the efficiency of the flushing. The wear debris present in the spark gap should be removed as quickly as possible. With poor flushing there is a possibility of build-up of the machined particles in the gap resulting in the short-circuiting and lower material removal rates. Problems with improper flushing are: uneven and significant tool wear affecting accuracy and surface finish; reduced removal rates due to unstable machining conditions and arcing around regions with high concentration of debris. It is noted during an experimental study that there is an optimum dielectric flushing rate of about 13 ml/s while machining AISI O1 tool steel, where the crack density and average thickness of the recast layer are at a minimum.

How to Calculate Radius of electrode from pressure flushing hole?

Radius of electrode from pressure flushing hole calculator uses Radius of the Electrodes = ((Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure))/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Pressure in the Flushing Gap)) to calculate the Radius of the Electrodes, Radius of electrode from pressure flushing hole formula is defined as radius of electrode tip used in process of unconventional machining by EDM. Radius of the Electrodes is denoted by R₀ symbol.

How to calculate Radius of electrode from pressure flushing hole using this online calculator? To use this online calculator for Radius of electrode from pressure flushing hole, enter Radial Location of Pressure (r), Pressure in Flushing Hole (P₁), Atmospheric Pressure (P_atm), Pressure in the Flushing Gap (P_r) & Radius of Flushing Hole (R₁) and hit the calculate button. Here is how the Radius of electrode from pressure flushing hole calculation can be explained with given input values -> 207.7324 = ((0.026)^((110000-101325)/(43800-101325))/0.02)^((43800-101325)/(110000-43800)).

FAQ

What is Radius of electrode from pressure flushing hole?

Radius of electrode from pressure flushing hole formula is defined as radius of electrode tip used in process of unconventional machining by EDM and is represented as R₀ = ((r)^((P₁-P_atm)/(P_r-P_atm))/R₁)^((P_r-P_atm)/(P₁-P_r)) or Radius of the Electrodes = ((Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure))/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Pressure in the Flushing Gap)). Radial location of pressure is the radial location of pressure during EDM, Pressure in Flushing Hole is the pressure in hole during EDM machining, Atmospheric pressure, also known as barometric pressure, is the pressure within the atmosphere of Earth, Pressure in the flushing gap is the pressure at any distance r in fluid flow passage through the electrode in the EDM process & Radius of flushing hole is the radius of flushing hole in EDM.

How to calculate Radius of electrode from pressure flushing hole?

Radius of electrode from pressure flushing hole formula is defined as radius of electrode tip used in process of unconventional machining by EDM is calculated using Radius of the Electrodes = ((Radial Location of Pressure)^((Pressure in Flushing Hole-Atmospheric Pressure)/(Pressure in the Flushing Gap-Atmospheric Pressure))/Radius of Flushing Hole)^((Pressure in the Flushing Gap-Atmospheric Pressure)/(Pressure in Flushing Hole-Pressure in the Flushing Gap)). To calculate Radius of electrode from pressure flushing hole, you need Radial Location of Pressure (r), Pressure in Flushing Hole (P₁), Atmospheric Pressure (P_atm), Pressure in the Flushing Gap (P_r) & Radius of Flushing Hole (R₁). With our tool, you need to enter the respective value for Radial Location of Pressure, Pressure in Flushing Hole, Atmospheric Pressure, Pressure in the Flushing Gap & Radius of Flushing Hole and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search