Strength of Joint per Pitch Length using Lap Joint with Single Shear Solution

STEP 0: Pre-Calculation Summary
Formula Used
Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
S = n*(1*(pi/4)*(Drivet^2)*Tsafe)
This formula uses 1 Constants, 4 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Variables Used
Strength of joint - (Measured in Newton) - Strength of joint is the strength of riveted joint per pitch length.
Number of Rivets Per Pitch - Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Safe shear stress - (Measured in Pascal) - Safe shear stress is always less than the yield shear stress.
STEP 1: Convert Input(s) to Base Unit
Number of Rivets Per Pitch: 2 --> No Conversion Required
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)
Safe shear stress: 0.24 Megapascal --> 240000 Pascal (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
S = n*(1*(pi/4)*(Drivet^2)*Tsafe) --> 2*(1*(pi/4)*(0.018^2)*240000)
Evaluating ... ...
S = 122.145122371571
STEP 3: Convert Result to Output's Unit
122.145122371571 Newton -->0.122145122371571 Kilonewton (Check conversion here)
FINAL ANSWER
0.122145122371571 0.122145 Kilonewton <-- Strength of joint
(Calculation completed in 00.004 seconds)

Credits

Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

22 Failure Due To Shearing Of Rivet Calculators

Diameter of rivet given strength of joint for butt joint with double cover plates
Go Rivet Diameter = sqrt(Safe load Joint/(Number of Rivets Per Pitch*2*(pi/4)*Safe shear stress))
Diameter of rivet given strength of joint for lap joint with single shear
Go Rivet Diameter = sqrt(Safe load Joint/(Number of Rivets Per Pitch*1*(pi/4)*Safe shear stress))
Number of rivets per pitch length given strength of joint for butt joint with double cover plates
Go Number of Rivets Per Pitch = Strength of joint/((2*(pi/4)*(Rivet Diameter^2)*Safe shear stress))
Number of rivets covered per pitch length given strength of joint for single shear lap joint
Go Number of Rivets Per Pitch = Strength of joint/((1*(pi/4)*(Rivet Diameter^2)*Safe shear stress))
Strength of Joint per Pitch Length using Butt Joint with Double Cover Plates
Go Strength of joint = Number of Rivets Per Pitch*(2*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Strength of Joint per Pitch Length using Lap Joint with Single Shear
Go Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Diameter of rivet given safe load for butt joint with double cover plates and double shear
Go Rivet Diameter = sqrt(Safe load Joint/(2*(pi/4)*Safe shear stress))
Diameter of rivets given safe load for triple-rivet butt joint with single cover plates
Go Rivet Diameter = sqrt(Safe load Joint/(3*(pi/4)*Safe shear stress))
Diameter of rivet given safe load for single rivet butt joint with single cover plates
Go Rivet Diameter = sqrt(Safe load Joint/(1*(pi/4)*Safe shear stress))
Diameter of rivet given safe load for double rivet butt joint with single cover plates
Go Rivet Diameter = sqrt(Safe load Joint/(2*(pi/4)*Safe shear stress))
Diameter of rivet given safe load per pitch length in single rivet lap joint
Go Rivet Diameter = sqrt(Safe load Joint/(1*(pi/4)*Safe shear stress))
Diameter of rivet given safe load per pitch length in double rivet lap joint
Go Rivet Diameter = sqrt(Safe load Joint/(2*(pi/4)*Safe shear stress))
Diameter of rivet given safe load per pitch length in triple-rivet lap joint
Go Rivet Diameter = sqrt(Safe load Joint/(3*(pi/4)*Safe shear stress))
Diameter of rivet given safe load for lap joint for single shear
Go Rivet Diameter = sqrt(Safe load Joint/(1*(pi/4)*Safe shear stress))
Safe Load per Pitch Length using Butt Joint with Double Cover Plates and Double Shear
Go Safe load Joint = (2*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe Load per Pitch Length using Single Rivet Butt Joint with Single Cover Plates
Go Safe load Joint = (1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe Load per Pitch Length using Double Rivet Butt Joint with Single Cover Plates
Go Safe load Joint = (2*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe Load per Pitch Length using Triple-Rivet Butt Joint with Single Cover Plates
Go Safe load Joint = (3*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe load rivet can withstand for lap joint of single shear
Go Safe load Joint = (1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe Load per Pitch Length using Single Rivet Lap Joint
Go Safe load Joint = (1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe Load per Pitch Length using Double Rivet Lap Joint
Go Safe load Joint = (2*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Safe load per pitch length given triple-rivet lap joint
Go Safe load Joint = (3*(pi/4)*(Rivet Diameter^2)*Safe shear stress)

Strength of Joint per Pitch Length using Lap Joint with Single Shear Formula

Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
S = n*(1*(pi/4)*(Drivet^2)*Tsafe)

What are rivets used for?

Rivets are ideal for supporting shear and tensile loads, as well as watertight applications. A rivet is a mechanical fastener consisting of a smooth, cylindrical shaft with a head. Upon installation, the end of the shaft expands, creating a “shop head” and fastening objects in place.

How to Calculate Strength of Joint per Pitch Length using Lap Joint with Single Shear?

Strength of Joint per Pitch Length using Lap Joint with Single Shear calculator uses Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress) to calculate the Strength of joint, The Strength of Joint per Pitch Length using Lap Joint with Single Shear formula is defined as the strength of riveted joint per pitch length of the rivet. Strength of joint is denoted by S symbol.

How to calculate Strength of Joint per Pitch Length using Lap Joint with Single Shear using this online calculator? To use this online calculator for Strength of Joint per Pitch Length using Lap Joint with Single Shear, enter Number of Rivets Per Pitch (n), Rivet Diameter (Drivet) & Safe shear stress (Tsafe) and hit the calculate button. Here is how the Strength of Joint per Pitch Length using Lap Joint with Single Shear calculation can be explained with given input values -> 0.000217 = 2*(1*(pi/4)*(0.018^2)*240000).

FAQ

What is Strength of Joint per Pitch Length using Lap Joint with Single Shear?
The Strength of Joint per Pitch Length using Lap Joint with Single Shear formula is defined as the strength of riveted joint per pitch length of the rivet and is represented as S = n*(1*(pi/4)*(Drivet^2)*Tsafe) or Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress). Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet, Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long & Safe shear stress is always less than the yield shear stress.
How to calculate Strength of Joint per Pitch Length using Lap Joint with Single Shear?
The Strength of Joint per Pitch Length using Lap Joint with Single Shear formula is defined as the strength of riveted joint per pitch length of the rivet is calculated using Strength of joint = Number of Rivets Per Pitch*(1*(pi/4)*(Rivet Diameter^2)*Safe shear stress). To calculate Strength of Joint per Pitch Length using Lap Joint with Single Shear, you need Number of Rivets Per Pitch (n), Rivet Diameter (Drivet) & Safe shear stress (Tsafe). With our tool, you need to enter the respective value for Number of Rivets Per Pitch, Rivet Diameter & Safe shear stress and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Strength of joint?
In this formula, Strength of joint uses Number of Rivets Per Pitch, Rivet Diameter & Safe shear stress. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Strength of joint = Number of Rivets Per Pitch*(2*(pi/4)*(Rivet Diameter^2)*Safe shear stress)
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!