Surface Area given Length of Sedimentation Tank with respect to Surface Area Calculator

✖Length of sedimentation tank is the bottom is slightly sloped to facilitate sludge scraping. The general dimension of a sedimentation tank are as follows: Length = 4 × Width.ⓘ Length of sedimentation tank [L_S]			+10% -10%
✖Cross-Sectional Area is the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point.ⓘ Cross-Sectional Area [A_cs]			+10% -10%
✖Height of Crack is the size of a flaw or crack in a material that can lead to catastrophic failure under a given stress.ⓘ Height of Crack [h]			+10% -10%

✖The area is the amount of two-dimensional space taken up by an object.ⓘ Surface Area given Length of Sedimentation Tank with respect to Surface Area [A]

⎘ Copy

👎

Formula

✖

Surface Area given Length of Sedimentation Tank with respect to Surface Area

Formula

`"A" = "L"_{"S"}*"A"_{"cs"}/"h"`

Example

`"48.75m²"="45m"*"13m²"/"12000mm"`

Calculator

LaTeX

Reset

👍

Download Environmental Engineering Formula PDF

Surface Area given Length of Sedimentation Tank with respect to Surface Area Solution

STEP 0: Pre-Calculation Summary

Formula Used

Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack
A = L_S*A_cs/h
This formula uses 4 Variables

Variables Used

Area - (Measured in Square Meter) - The area is the amount of two-dimensional space taken up by an object.
Length of sedimentation tank - (Measured in Meter) - Length of sedimentation tank is the bottom is slightly sloped to facilitate sludge scraping. The general dimension of a sedimentation tank are as follows: Length = 4 × Width.
Cross-Sectional Area - (Measured in Square Meter) - Cross-Sectional Area is the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point.
Height of Crack - (Measured in Meter) - Height of Crack is the size of a flaw or crack in a material that can lead to catastrophic failure under a given stress.

STEP 1: Convert Input(s) to Base Unit

Length of sedimentation tank: 45 Meter --> 45 Meter No Conversion Required
Cross-Sectional Area: 13 Square Meter --> 13 Square Meter No Conversion Required
Height of Crack: 12000 Millimeter --> 12 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A = L_S*A_cs/h --> 45*13/12

Evaluating ... ...

A = 48.75

STEP 3: Convert Result to Output's Unit

48.75 Square Meter --> No Conversion Required

FINAL ANSWER

48.75 Square Meter <-- Area

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Environmental Engineering » Treatment of Water 1: Sedimentation » Surface Area of Tank » Surface Area given Length of Sedimentation Tank with respect to Surface Area

Credits

Created by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has created this Calculator and 500+ more calculators!

Verified by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has verified this Calculator and 600+ more calculators!

< 5 Surface Area of Tank Calculators

Surface Area given Length of Sedimentation Tank with respect to Surface Area

Go Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack

Surface Area with respect to Settling Velocity

Go Area = Cross-Sectional Area*Falling Speed/Settling Velocity

Surface Area with respect to Darcy Weishbach Friction Factor

Go Area = Cross-Sectional Area*sqrt(8/Darcy Friction Factor)

Surface Area of Sedimentation Tank

Go Area = Width*Length of sedimentation tank

Surface Area with respect to Cross-section Area for Practical Purpose

Go Area = 10*Cross-Sectional Area

Surface Area given Length of Sedimentation Tank with respect to Surface Area Formula

Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack
A = L_S*A_cs/h

What is Sedimentation?

Sedimentation is the tendency for particles in suspension to settle out of the fluid in which they are entrained and come to rest against a barrier. This is due to their motion through the fluid in response to the forces acting on them: these forces can be due to gravity, centrifugal acceleration, or electromagnetism.

How to Calculate Surface Area given Length of Sedimentation Tank with respect to Surface Area?

Surface Area given Length of Sedimentation Tank with respect to Surface Area calculator uses Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack to calculate the Area, The Surface Area given Length of Sedimentation Tank with respect to Surface Area is defined as the measure of total area that surface of object occupies. Area is denoted by A symbol.

How to calculate Surface Area given Length of Sedimentation Tank with respect to Surface Area using this online calculator? To use this online calculator for Surface Area given Length of Sedimentation Tank with respect to Surface Area, enter Length of sedimentation tank (L_S), Cross-Sectional Area (A_cs) & Height of Crack (h) and hit the calculate button. Here is how the Surface Area given Length of Sedimentation Tank with respect to Surface Area calculation can be explained with given input values -> 48.75 = 45*13/12.

FAQ

What is Surface Area given Length of Sedimentation Tank with respect to Surface Area?

The Surface Area given Length of Sedimentation Tank with respect to Surface Area is defined as the measure of total area that surface of object occupies and is represented as A = L_S*A_cs/h or Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack. Length of sedimentation tank is the bottom is slightly sloped to facilitate sludge scraping. The general dimension of a sedimentation tank are as follows: Length = 4 × Width, Cross-Sectional Area is the area of a two-dimensional shape that is obtained when a three-dimensional shape is sliced perpendicular to some specified axis at a point & Height of Crack is the size of a flaw or crack in a material that can lead to catastrophic failure under a given stress.

How to calculate Surface Area given Length of Sedimentation Tank with respect to Surface Area?

The Surface Area given Length of Sedimentation Tank with respect to Surface Area is defined as the measure of total area that surface of object occupies is calculated using Area = Length of sedimentation tank*Cross-Sectional Area/Height of Crack. To calculate Surface Area given Length of Sedimentation Tank with respect to Surface Area, you need Length of sedimentation tank (L_S), Cross-Sectional Area (A_cs) & Height of Crack (h). With our tool, you need to enter the respective value for Length of sedimentation tank, Cross-Sectional Area & Height of Crack and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Area?

In this formula, Area uses Length of sedimentation tank, Cross-Sectional Area & Height of Crack. We can use 4 other way(s) to calculate the same, which is/are as follows -

Area = Width*Length of sedimentation tank
Area = Cross-Sectional Area*Falling Speed/Settling Velocity
Area = Cross-Sectional Area*sqrt(8/Darcy Friction Factor)
Area = 10*Cross-Sectional Area

Home

FREE PDFs

🔍 Search