Thickness of plates given safe load which rivet can withstand against crushing Solution

STEP 0: Pre-Calculation Summary
Formula Used
Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter)
tplate = Psafe/(σc*Drivet)
This formula uses 4 Variables
Variables Used
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Safe load Joint - (Measured in Newton) - Safe load Joint is the manufacturer's recommended maximum weight load for a line, rope, crane, or any other lifting device or component of a lifting device.
Crushing stress - (Measured in Pascal) - Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
STEP 1: Convert Input(s) to Base Unit
Safe load Joint: 4.5 Kilonewton --> 4500 Newton (Check conversion here)
Crushing stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
tplate = Psafe/(σc*Drivet) --> 4500/(2400000*0.018)
Evaluating ... ...
tplate = 0.104166666666667
STEP 3: Convert Result to Output's Unit
0.104166666666667 Meter -->104.166666666667 Millimeter (Check conversion here)
FINAL ANSWER
104.166666666667 104.1667 Millimeter <-- Thickness of Plate
(Calculation completed in 00.004 seconds)

Credits

Created by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has created this Calculator and 2000+ more calculators!
Verified by Payal Priya
Birsa Institute of Technology (BIT), Sindri
Payal Priya has verified this Calculator and 1900+ more calculators!

24 Failure Due To Crushing Of Rivet Or Plate Calculators

Allowable crushing stress given strength of joint per pitch length of joint against crushing
Go Crushing stress = Strength of joint/(Number of Rivets Per Pitch*Rivet Diameter*Thickness of Plate)
Thickness of plates given strength of joint per pitch length of joint against crushing
Go Thickness of Plate = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)
Diameter of rivet given strength of joint per pitch length of joint against crushing
Go Rivet Diameter = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Thickness of Plate)
Number of rivets given strength of joint per pitch length of joint against crushing
Go Number of Rivets Per Pitch = Strength of joint/(Crushing stress*Rivet Diameter*Thickness of Plate)
Strength of joint per pitch length of joint against crushing
Go Strength of joint = (Number of Rivets Per Pitch*Crushing stress*Rivet Diameter*Thickness of Plate)
Allowable crushing stress given strength of joint per pitch length (single rivet)
Go Crushing stress = Strength of joint/(1*Rivet Diameter*Thickness of Plate)
Allowable crushing stress given strength of joint per pitch length (double rivet)
Go Crushing stress = Strength of joint/(2*Rivet Diameter*Thickness of Plate)
Allowable crushing stress given strength of joint per pitch length (triple rivet)
Go Crushing stress = Strength of joint/(3*Rivet Diameter*Thickness of Plate)
Thickness of plates given strength of joint per pitch length (single rivet)
Go Thickness of Plate = Strength of joint/(1*Crushing stress*Rivet Diameter)
Thickness of plates given strength of joint per pitch length (double rivet)
Go Thickness of Plate = Strength of joint/(2*Crushing stress*Rivet Diameter)
Strength of joint per pitch length of joint against crushing (triple rivet)
Go Strength of joint = (3*Crushing stress*Rivet Diameter*Thickness of Plate)
Thickness of plates given strength of joint per pitch length (triple rivet)
Go Thickness of Plate = Strength of joint/(3*Crushing stress*Rivet Diameter)
Strength of joint per pitch length of joint against crushing(single rivet)
Go Strength of joint = (1*Crushing stress*Rivet Diameter*Thickness of Plate)
Strength of joint per pitch length of joint against crushing(double rivet)
Go Strength of joint = (2*Crushing stress*Rivet Diameter*Thickness of Plate)
Diameter of rivet given strength of joint per pitch length (single rivet)
Go Rivet Diameter = Strength of joint/(1*Crushing stress*Thickness of Plate)
Diameter of rivet given strength of joint per pitch length (double rivet)
Go Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate)
Diameter of rivet given strength of joint per pitch length (triple-rivet)
Go Rivet Diameter = Strength of joint/(3*Crushing stress*Thickness of Plate)
Allowable crushing stress given safe load which rivet can withstand against crushing
Go Crushing stress = Safe load Joint/(Rivet Diameter*Thickness of Plate)
Thickness of plates given safe load which rivet can withstand against crushing
Go Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter)
Diameter of rivet given safe load that rivet can withstand against crushing
Go Rivet Diameter = Safe load Joint/(Crushing stress*Thickness of Plate)
Safe load which rivet can withstand against crushing
Go Safe load Joint = Crushing stress*Rivet Diameter*Thickness of Plate
Allowable crushing stress given safe load which rivet can withstand for given projected area
Go Crushing stress = Safe load Joint/(Projected area)
Projected area given safe load which rivet can withstand against crushing
Go Projected area = Safe load Joint/(Crushing stress)
Safe load which rivet can withstand against crushing given projected area
Go Safe load Joint = Crushing stress*Projected area

Thickness of plates given safe load which rivet can withstand against crushing Formula

Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter)
tplate = Psafe/(σc*Drivet)

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Thickness of plates given safe load which rivet can withstand against crushing?

Thickness of plates given safe load which rivet can withstand against crushing calculator uses Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter) to calculate the Thickness of Plate, The Thickness of plates given safe load which rivet can withstand against crushing formula is defined as the thickness of the thickest sheet that is being joined. Thickness of Plate is denoted by tplate symbol.

How to calculate Thickness of plates given safe load which rivet can withstand against crushing using this online calculator? To use this online calculator for Thickness of plates given safe load which rivet can withstand against crushing, enter Safe load Joint (Psafe), Crushing stress c) & Rivet Diameter (Drivet) and hit the calculate button. Here is how the Thickness of plates given safe load which rivet can withstand against crushing calculation can be explained with given input values -> 78125 = 4500/(2400000*0.018).

FAQ

What is Thickness of plates given safe load which rivet can withstand against crushing?
The Thickness of plates given safe load which rivet can withstand against crushing formula is defined as the thickness of the thickest sheet that is being joined and is represented as tplate = Psafe/(σc*Drivet) or Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter). Safe load Joint is the manufacturer's recommended maximum weight load for a line, rope, crane, or any other lifting device or component of a lifting device, Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest & Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
How to calculate Thickness of plates given safe load which rivet can withstand against crushing?
The Thickness of plates given safe load which rivet can withstand against crushing formula is defined as the thickness of the thickest sheet that is being joined is calculated using Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter). To calculate Thickness of plates given safe load which rivet can withstand against crushing, you need Safe load Joint (Psafe), Crushing stress c) & Rivet Diameter (Drivet). With our tool, you need to enter the respective value for Safe load Joint, Crushing stress & Rivet Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Thickness of Plate?
In this formula, Thickness of Plate uses Safe load Joint, Crushing stress & Rivet Diameter. We can use 4 other way(s) to calculate the same, which is/are as follows -
  • Thickness of Plate = Strength of joint/(1*Crushing stress*Rivet Diameter)
  • Thickness of Plate = Strength of joint/(2*Crushing stress*Rivet Diameter)
  • Thickness of Plate = Strength of joint/(3*Crushing stress*Rivet Diameter)
  • Thickness of Plate = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!