Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation Solution

STEP 0: Pre-Calculation Summary
Formula Used
Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut)
ac = Pf/(C*ρwork piece*Vcutting*θf*dcut)
This formula uses 7 Variables
Variables Used
Undeformed Chip Thickness - (Measured in Meter) - Undeformed Chip Thickness in milling is defined as the distance between two consecutive cut surfaces.
Rate of Heat Gen in Secondary Shear Zone - (Measured in Watt) - The Rate of Heat Gen in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip-tool contact region.
Specific Heat Capacity of Workpiece - (Measured in Joule per Kilogram per K) - The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius.
Density of work piece - (Measured in Kilogram per Cubic Meter) - The Density of work piece is the mass per unit volume ratio of the material of workpiece.
Cutting Speed - (Measured in Meter per Second) - Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute).
Average Temp Rise of Chip in Secondary Shear Zone - (Measured in Kelvin) - The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone.
Depth of Cut - (Measured in Meter) - Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.
STEP 1: Convert Input(s) to Base Unit
Rate of Heat Gen in Secondary Shear Zone: 400 Watt --> 400 Watt No Conversion Required
Specific Heat Capacity of Workpiece: 502 Joule per Kilogram per K --> 502 Joule per Kilogram per K No Conversion Required
Density of work piece: 7200 Kilogram per Cubic Meter --> 7200 Kilogram per Cubic Meter No Conversion Required
Cutting Speed: 2 Meter per Second --> 2 Meter per Second No Conversion Required
Average Temp Rise of Chip in Secondary Shear Zone: 88.5 Degree Celsius --> 88.5 Kelvin (Check conversion here)
Depth of Cut: 2.5 Millimeter --> 0.0025 Meter (Check conversion here)
STEP 2: Evaluate Formula
Substituting Input Values in Formula
ac = Pf/(C*ρwork piece*Vcuttingf*dcut) --> 400/(502*7200*2*88.5*0.0025)
Evaluating ... ...
ac = 0.000250098163529185
STEP 3: Convert Result to Output's Unit
0.000250098163529185 Meter -->0.250098163529185 Millimeter (Check conversion here)
FINAL ANSWER
0.250098163529185 0.250098 Millimeter <-- Undeformed Chip Thickness
(Calculation completed in 00.004 seconds)

Credits

Created by Parul Keshav
National Institute of Technology (NIT), Srinagar
Parul Keshav has created this Calculator and 300+ more calculators!
Verified by Kumar Siddhant
Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur
Kumar Siddhant has verified this Calculator and 100+ more calculators!

18 Temperatures in Metal Cutting Calculators

Undeformed Chip Thickness given Average Temperature Rise of Material under Primary Shear Zone
Go Undeformed Chip Thickness = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of work piece*Specific Heat Capacity of Workpiece*Cutting Speed*Average Temperature Rise*Depth of Cut)
Density of Material using Average Temperature Rise of material under Primary Shear Zone
Go Density of work piece = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Average Temperature Rise*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)
Specific Heat given Average Temperature Rise of Material under Primary Shear Zone
Go Specific Heat Capacity of Workpiece = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of work piece*Average Temperature Rise*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)
Cutting Speed given Average Temperature Rise of Material under Primary Shear Zone
Go Cutting Speed = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of work piece*Specific Heat Capacity of Workpiece*Average Temperature Rise*Undeformed Chip Thickness*Depth of Cut)
Depth of Cut given Average Temperature Rise of Material under Primary Shear Zone
Go Depth of Cut = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of work piece*Specific Heat Capacity of Workpiece*Cutting Speed*Undeformed Chip Thickness*Average Temperature Rise)
Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation
Go Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut)
Specific Heat using Average Temperature Rise of Chip from Secondary Deformation
Go Specific Heat Capacity of Workpiece = Rate of Heat Gen in Secondary Shear Zone/(Average Temp Rise of Chip in Secondary Shear Zone*Density of work piece*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)
Depth of Cut using Average Temperature Rise of Chip from Secondary Deformation
Go Depth of Cut = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Undeformed Chip Thickness*Average Temp Rise of Chip in Secondary Shear Zone)
Density of Material using Average Temperature rise of Chip from Secondary Deformation
Go Density of work piece = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Average Temp Rise of Chip in Secondary Shear Zone*Cutting Speed*Undeformed Chip Thickness*Depth of Cut)
Cutting Speed using Average Temperature Rise of Chip from Secondary Deformation
Go Cutting Speed = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Average Temp Rise of Chip in Secondary Shear Zone*Undeformed Chip Thickness*Depth of Cut)
Length of Heat Source per Chip Thickness using Max Temperature Rise in Secondary Shear Zone
Go Length of Heat Source per Chip Thickness = Thermal Number/((Max Temp in Chip in Secondary Deformation Zone/(Average Temp Rise of Chip in Secondary Shear Zone*1.13))^2)
Thermal Number using Maximum Temperature Rise in Chip in Secondary Deformation Zone
Go Thermal Number = Length of Heat Source per Chip Thickness*((Max Temp in Chip in Secondary Deformation Zone/(Average Temp Rise of Chip in Secondary Shear Zone*1.13))^2)
Rate of Heat Conduction into Workpiece given Total Rate of Heat Generation
Go Rate of Heat Conduction into the Workpiece = Total Rate of Heat Generation in Metal Cutting-Rate of Heat Transportation by Chip-Rate of Heat Conduction into the Tool
Rate of Heat Transportation by Chip given Total Rate of Heat Generation
Go Rate of Heat Transportation by Chip = Total Rate of Heat Generation in Metal Cutting-Rate of Heat Conduction into the Workpiece-Rate of Heat Conduction into the Tool
Rate of Heat Conduction into Tool given Total Rate of Heat Generation
Go Rate of Heat Conduction into the Tool = Total Rate of Heat Generation in Metal Cutting-Rate of Heat Transportation by Chip-Rate of Heat Conduction into the Workpiece
Initial Workpiece Temperature using Maximum Temperature in Secondary Deformation Zone
Go Initial Workpiece Temperature = Max Temp in Chip in Secondary Deformation Zone-Temperature Rise in Secondary Deformation-Temperature Rise in Primary Deformation
Maximum temperature in secondary deformation zone
Go Max Temp in Chip in Secondary Deformation Zone = Temperature Rise in Secondary Deformation+Temperature Rise in Primary Deformation+Initial Workpiece Temperature
Rate of Energy Consumption using Rate of Heat Generation during Machining
Go Rate of Energy Consumption during Machining = Rate of Heat Generation in Primary Shear Zone+Rate of Heat Gen in Secondary Shear Zone

Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation Formula

Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut)
ac = Pf/(C*ρwork piece*Vcutting*θf*dcut)

What is un-deformed chip thickness?

The un-deformed chip thickness in milling is defined as the distance between two consecutive cut surfaces. It varies during cutting and is measured in the direction perpendicular to the preceding cut surface

How to Calculate Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation?

Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation calculator uses Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut) to calculate the Undeformed Chip Thickness, The Un-deformed chip thickness using Average Temperature rise of chip from secondary deformation is defined as the distance between two consecutive cut surfaces. Undeformed Chip Thickness is denoted by ac symbol.

How to calculate Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation using this online calculator? To use this online calculator for Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation, enter Rate of Heat Gen in Secondary Shear Zone (Pf), Specific Heat Capacity of Workpiece (C), Density of work piece work piece), Cutting Speed (Vcutting), Average Temp Rise of Chip in Secondary Shear Zone f) & Depth of Cut (dcut) and hit the calculate button. Here is how the Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation calculation can be explained with given input values -> 250.0982 = 400/(502*7200*2*88.5*0.0025) .

FAQ

What is Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation?
The Un-deformed chip thickness using Average Temperature rise of chip from secondary deformation is defined as the distance between two consecutive cut surfaces and is represented as ac = Pf/(C*ρwork piece*Vcuttingf*dcut) or Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut). The Rate of Heat Gen in Secondary Shear Zone is the rate of heat generation in the area surrounding the chip-tool contact region, The Specific Heat Capacity of Workpiece is the amount of heat per unit mass required to raise the temperature by one degree Celsius, The Density of work piece is the mass per unit volume ratio of the material of workpiece, Cutting Speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute), The Average Temp Rise of Chip in Secondary Shear Zone is defined as the amount of temperature rise in the secondary shear zone & Depth of Cut is the tertiary cutting motion that provides a necessary depth of material that is required to remove by machining. It is usually given in the third perpendicular direction.
How to calculate Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation?
The Un-deformed chip thickness using Average Temperature rise of chip from secondary deformation is defined as the distance between two consecutive cut surfaces is calculated using Undeformed Chip Thickness = Rate of Heat Gen in Secondary Shear Zone/(Specific Heat Capacity of Workpiece*Density of work piece*Cutting Speed*Average Temp Rise of Chip in Secondary Shear Zone*Depth of Cut). To calculate Un-deformed Chip Thickness using Average Temperature Rise of Chip from Secondary Deformation, you need Rate of Heat Gen in Secondary Shear Zone (Pf), Specific Heat Capacity of Workpiece (C), Density of work piece work piece), Cutting Speed (Vcutting), Average Temp Rise of Chip in Secondary Shear Zone f) & Depth of Cut (dcut). With our tool, you need to enter the respective value for Rate of Heat Gen in Secondary Shear Zone, Specific Heat Capacity of Workpiece, Density of work piece, Cutting Speed, Average Temp Rise of Chip in Secondary Shear Zone & Depth of Cut and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate Undeformed Chip Thickness?
In this formula, Undeformed Chip Thickness uses Rate of Heat Gen in Secondary Shear Zone, Specific Heat Capacity of Workpiece, Density of work piece, Cutting Speed, Average Temp Rise of Chip in Secondary Shear Zone & Depth of Cut. We can use 1 other way(s) to calculate the same, which is/are as follows -
  • Undeformed Chip Thickness = ((1-Fraction of Heat Conducted into the workpiece)*Rate of Heat Generation in Primary Shear Zone)/(Density of work piece*Specific Heat Capacity of Workpiece*Cutting Speed*Average Temperature Rise*Depth of Cut)
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!