Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) Calculator

✖Resistivity is the measure of how strongly a material opposes the flow of current through them.ⓘ Resistivity [ρ]			+10% -10%
✖Current Overhead AC is defined as the current flowing through the overhead ac supply wire.ⓘ Current Overhead AC [I]			+10% -10%
✖Length of Overhead AC Wire is the total length of the wire from one end to other end.ⓘ Length of Overhead AC Wire [L]			+10% -10%
✖Line Losses is defined as the total losses occurring in an Overhead AC line when in use.ⓘ Line Losses [P_loss]			+10% -10%

✖Volume of Conductor is the total volume of the material used to make the conductor of an overhead ac line.ⓘ Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) [V]

⎘ Copy

👎

Formula

✖

Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)

Formula

`"V" = 4*"ρ"*("I"*"L")^2/("P"_{"loss"})`

Example

`"0.04445m³"=4*"0.000017Ω*m"*("6.9A"*"10.63m")^2/("8.23W")`

Calculator

LaTeX

Reset

👍

Download Power System Formula PDF

Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses)
V = 4*ρ*(I*L)^2/(P_loss)
This formula uses 5 Variables

Variables Used

Volume of Conductor - (Measured in Cubic Meter) - Volume of Conductor is the total volume of the material used to make the conductor of an overhead ac line.
Resistivity - (Measured in Ohm Meter) - Resistivity is the measure of how strongly a material opposes the flow of current through them.
Current Overhead AC - (Measured in Ampere) - Current Overhead AC is defined as the current flowing through the overhead ac supply wire.
Length of Overhead AC Wire - (Measured in Meter) - Length of Overhead AC Wire is the total length of the wire from one end to other end.
Line Losses - (Measured in Watt) - Line Losses is defined as the total losses occurring in an Overhead AC line when in use.

STEP 1: Convert Input(s) to Base Unit

Resistivity: 1.7E-05 Ohm Meter --> 1.7E-05 Ohm Meter No Conversion Required
Current Overhead AC: 6.9 Ampere --> 6.9 Ampere No Conversion Required
Length of Overhead AC Wire: 10.63 Meter --> 10.63 Meter No Conversion Required
Line Losses: 8.23 Watt --> 8.23 Watt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V = 4*ρ*(I*L)^2/(P_loss) --> 4*1.7E-05*(6.9*10.63)^2/(8.23)

Evaluating ... ...

V = 0.0444502070245444

STEP 3: Convert Result to Output's Unit

0.0444502070245444 Cubic Meter --> No Conversion Required

FINAL ANSWER

0.0444502070245444 ≈ 0.04445 Cubic Meter <-- Volume of Conductor

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power System » Overhead AC Supply » 1-Φ 3-Wire System » Wire Parameters » Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< 19 Wire Parameters Calculators

Length using Volume of Conductor Material (Single-Phase Three-Wire OS)

Go Length of Overhead AC Wire = sqrt(Volume of Conductor*Line Losses*(cos(Phase Difference)*Maximum Voltage Overhead AC)^2/((2.5)*Resistivity*(Power Transmitted^2)))

Line Losses using Area of X-Section(Single-Phase Three-Wire OS)

Go Line Losses = (Length of Overhead AC Wire*Resistivity*(Power Transmitted^2))/(Area of Overhead AC Wire*(Maximum Voltage Overhead AC^2)*((cos(Phase Difference))^2))

Length of Wire using Area of X-Section(Single-Phase Three-Wire OS)

Go Length of Overhead AC Wire = Area of Overhead AC Wire*(Maximum Voltage Overhead AC^2)*Line Losses*((cos(Phase Difference))^2)/(Resistivity*(Power Transmitted^2))

Area of X-Section(Single-Phase Three-Wire OS)

Go Area of Overhead AC Wire = (Power Transmitted^2)*Resistivity*Length of Overhead AC Wire/(((cos(Phase Difference))^2)*Line Losses*(Maximum Voltage Overhead AC^2))

Line Losses using Volume of Conductor Material (Single-Phase Three-Wire OS)

Go Line Losses = 2.5*(Power Transmitted)^2*Resistivity*(Length of Overhead AC Wire)^2/((Maximum Voltage Overhead AC*cos(Phase Difference))^2*Volume of Conductor)

Area of X-Section using Line Losses (Single-Phase Three-Wire OS)

Go Area of Overhead AC Wire = Resistivity*Length of Overhead AC Wire*(Power Transmitted)^2/(Line Losses*(Maximum Voltage Overhead AC*cos(Phase Difference))^2)

Length using Line Losses (Single-Phase Three-Wire OS)

Go Length of Overhead AC Wire = Line Losses*Area of Overhead AC Wire*(Maximum Voltage Overhead AC*cos(Phase Difference))^2/((Power Transmitted^2)*Resistivity)

Volume of Conductor Material using Line Losses (Single-Phase Three-Wire OS)

Go Volume of Conductor = Resistivity*(Power Transmitted*Length of Overhead AC Wire)^2/(Line Losses*(Maximum Voltage Overhead AC*cos(Phase Difference))^2)

Constant using Load Current (Single-Phase Three-Wire OS)

Go Constant Overhead AC = 32*Resistivity*(Current Overhead AC*Length of Overhead AC Wire*cos(Phase Difference))^2/Line Losses

Constant using Line Losses (Single-Phase Three-Wire OS)

Go Constant Overhead AC = (4*Resistivity*(Power Transmitted*Length of Overhead AC Wire)^2)/(Line Losses*(Maximum Voltage Overhead AC)^2)

Constant(Single-Phase Three-Wire OS)

Go Constant Overhead AC = (4*(Power Transmitted^2)*Resistivity*Length of Overhead AC Wire)/(Line Losses*(Voltage Overhead AC^2))

Area of X-Section using Load Current (Single-Phase Three-Wire OS)

Go Area of Overhead AC Wire = 2*Resistivity*Length of Overhead AC Wire*(Current Overhead AC)^2/(Line Losses)

Length using Load Current (Single-Phase Three-Wire OS)

Go Length of Overhead AC Wire = Line Losses*Area of Overhead AC Wire/(2*(Current Overhead AC^2)*Resistivity)

Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)

Go Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses)

Constant using Volume of Conductor Material (Single-Phase Three-Wire OS)

Go Constant Overhead AC = Volume of Conductor*(cos(Phase Difference))^2/(0.625)

Area of X-section using Volume of Conductor Material (Single-Phase Three-Wire OS)

Go Area of Overhead AC Wire = Volume of Conductor/((2.5)*Length of Overhead AC Wire)

Volume of Conductor Material(Single-Phase Three-Wire OS)

Go Volume of Conductor = (2.5)*Area of Overhead AC Wire*Length of Overhead AC Wire

Line Losses(Single-Phase Three-Wire OS)

Go Line Losses = (2)*((Current Overhead AC)^2)*Resistance Overhead AC

Line Losses using Load Current (Single-Phase Three-Wire OS)

Go Line Losses = 2*Resistance Overhead AC*(Current Overhead AC)^2

Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) Formula

Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses)
V = 4*ρ*(I*L)^2/(P_loss)

What is the value of maximum voltage and volume of conductor material in 1-phase 3-wire system?

The volume of conductor material required in this system is 5/8cos²θ times that of 2-wire d.c.system with the one conductor earthed. The maximum voltage between conductors is 2v_m so that r.m.s. value of voltage between them is √2/v_m.

How to Calculate Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)?

Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) calculator uses Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses) to calculate the Volume of Conductor, The Volume of Conductor Material using Load Current (single-Phase three-Wire OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase three-wire overhead system. Volume of Conductor is denoted by V symbol.

How to calculate Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) using this online calculator? To use this online calculator for Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS), enter Resistivity (ρ), Current Overhead AC (I), Length of Overhead AC Wire (L) & Line Losses (P_loss) and hit the calculate button. Here is how the Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS) calculation can be explained with given input values -> 0.04445 = 4*1.7E-05*(6.9*10.63)^2/(8.23).

FAQ

What is Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)?

The Volume of Conductor Material using Load Current (single-Phase three-Wire OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase three-wire overhead system and is represented as V = 4*ρ*(I*L)^2/(P_loss) or Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses). Resistivity is the measure of how strongly a material opposes the flow of current through them, Current Overhead AC is defined as the current flowing through the overhead ac supply wire, Length of Overhead AC Wire is the total length of the wire from one end to other end & Line Losses is defined as the total losses occurring in an Overhead AC line when in use.

How to calculate Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS)?

The Volume of Conductor Material using Load Current (single-Phase three-Wire OS) formula is defined as the 3-dimensional space enclosed by a conductor material of a single-phase three-wire overhead system is calculated using Volume of Conductor = 4*Resistivity*(Current Overhead AC*Length of Overhead AC Wire)^2/(Line Losses). To calculate Volume of Conductor Material using Load Current (Single-Phase Three-Wire OS), you need Resistivity (ρ), Current Overhead AC (I), Length of Overhead AC Wire (L) & Line Losses (P_loss). With our tool, you need to enter the respective value for Resistivity, Current Overhead AC, Length of Overhead AC Wire & Line Losses and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Volume of Conductor?

In this formula, Volume of Conductor uses Resistivity, Current Overhead AC, Length of Overhead AC Wire & Line Losses. We can use 2 other way(s) to calculate the same, which is/are as follows -

Volume of Conductor = (2.5)*Area of Overhead AC Wire*Length of Overhead AC Wire
Volume of Conductor = Resistivity*(Power Transmitted*Length of Overhead AC Wire)^2/(Line Losses*(Maximum Voltage Overhead AC*cos(Phase Difference))^2)

Home

FREE PDFs

🔍 Search