Water Table Depth given Distance in Tracer Method Calculator

✖Channel Width is the width of the path through which the flow occurs in any stream or reservoir.ⓘ Channel Width [W]			+10% -10%
✖Estimated Distance is the total movement of river flow without regard to direction. It represents how much ground river flow has covered during its motion.ⓘ Estimated Distance [L]			+10% -10%

✖Water Depth as Indicated by the Scale is the depth as measured from the water level to the bottom of the considered water body.ⓘ Water Table Depth given Distance in Tracer Method [d]

⎘ Copy

👎

Formula

✖

Water Table Depth given Distance in Tracer Method

Formula

`"d" = (100*"W"^2)/"L"`

Example

`"192.3077m"=(100*("10m")^2)/"52m"`

Calculator

LaTeX

Reset

👍

Download Discharge Measurements Formulas PDF

Water Table Depth given Distance in Tracer Method Solution

STEP 0: Pre-Calculation Summary

Formula Used

Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance
d = (100*W^2)/L
This formula uses 3 Variables

Variables Used

Water Depth as Indicated by the Scale - (Measured in Meter) - Water Depth as Indicated by the Scale is the depth as measured from the water level to the bottom of the considered water body.
Channel Width - (Measured in Meter) - Channel Width is the width of the path through which the flow occurs in any stream or reservoir.
Estimated Distance - (Measured in Meter) - Estimated Distance is the total movement of river flow without regard to direction. It represents how much ground river flow has covered during its motion.

STEP 1: Convert Input(s) to Base Unit

Channel Width: 10 Meter --> 10 Meter No Conversion Required
Estimated Distance: 52 Meter --> 52 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

d = (100*W^2)/L --> (100*10^2)/52

Evaluating ... ...

d = 192.307692307692

STEP 3: Convert Result to Output's Unit

192.307692307692 Meter --> No Conversion Required

FINAL ANSWER

192.307692307692 ≈ 192.3077 Meter <-- Water Depth as Indicated by the Scale

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Engineering Hydrology » Discharge Measurements » Measurement Methods » Tracer Method (Instantaneous Injection) » Water Table Depth given Distance in Tracer Method

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by Himanshi Sharma

Bhilai Institute of Technology (BIT), Raipur

Himanshi Sharma has verified this Calculator and 800+ more calculators!

< 3 Tracer Method (Instantaneous Injection) Calculators

Water Table Depth given Distance in Tracer Method

Go Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance

Estimated Distance given Channel Width

Go Estimated Distance = (100*Channel Width^2)/Water Depth as Indicated by the Scale

Estimated Distance given Discharge in Tracer Method

Go Estimated Distance = 50*sqrt(Discharge)

Water Table Depth given Distance in Tracer Method Formula

Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance
d = (100*W^2)/L

What is Tracer Method?

The tracer method is a dilution method of determining the flow rate in a ground or surface water environment where a hydraulic structure (flume/weir) cannot be installed either due to cost, monitoring duration, or ecological reasons.

What are the advantages and limitations of using the Tracer Method?

The tracer method provides accurate and reliable data on water movement and can be used to identify and track contaminants in the water system.
The tracer method can be expensive and time-consuming, and there may be limitations to the types of tracers that can be used in different environments.

How to Calculate Water Table Depth given Distance in Tracer Method?

Water Table Depth given Distance in Tracer Method calculator uses Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance to calculate the Water Depth as Indicated by the Scale, The Water Table Depth given Distance in Tracer Method formula is defined as a technique used to estimate the depth of the water table (the upper surface of the zone of saturation) along a river or channel involves injecting a tracer (usually a chemical compound) into the subsurface and observing its dispersion downstream. Water Depth as Indicated by the Scale is denoted by d symbol.

How to calculate Water Table Depth given Distance in Tracer Method using this online calculator? To use this online calculator for Water Table Depth given Distance in Tracer Method, enter Channel Width (W) & Estimated Distance (L) and hit the calculate button. Here is how the Water Table Depth given Distance in Tracer Method calculation can be explained with given input values -> 200 = (100*10^2)/52.

FAQ

What is Water Table Depth given Distance in Tracer Method?

The Water Table Depth given Distance in Tracer Method formula is defined as a technique used to estimate the depth of the water table (the upper surface of the zone of saturation) along a river or channel involves injecting a tracer (usually a chemical compound) into the subsurface and observing its dispersion downstream and is represented as d = (100*W^2)/L or Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance. Channel Width is the width of the path through which the flow occurs in any stream or reservoir & Estimated Distance is the total movement of river flow without regard to direction. It represents how much ground river flow has covered during its motion.

How to calculate Water Table Depth given Distance in Tracer Method?

The Water Table Depth given Distance in Tracer Method formula is defined as a technique used to estimate the depth of the water table (the upper surface of the zone of saturation) along a river or channel involves injecting a tracer (usually a chemical compound) into the subsurface and observing its dispersion downstream is calculated using Water Depth as Indicated by the Scale = (100*Channel Width^2)/Estimated Distance. To calculate Water Table Depth given Distance in Tracer Method, you need Channel Width (W) & Estimated Distance (L). With our tool, you need to enter the respective value for Channel Width & Estimated Distance and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search