Width of U Collar given Initial Bolt Load to Seat Gasket Joint Calculator

✖Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.ⓘ Initial bolt load to seat the gasket joint [W_m2]			+10% -10%
✖Gasket Diameter is a straight line passing from side to side through the centre of a gasket.ⓘ Gasket Diameter [G]			+10% -10%
✖Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.ⓘ Gasket Unit Seating Load [y_sl]			+10% -10%

✖Width of u-collar is definied as the measurement or extent of u-collar from side to side.ⓘ Width of U Collar given Initial Bolt Load to Seat Gasket Joint [b]

⎘ Copy

👎

Formula

✖

Width of U Collar given Initial Bolt Load to Seat Gasket Joint

Formula

`"b" = "W"_{"m2"}/(pi*"G"*"y"_{"sl"})`

Example

`"4.146813mm"="1605N"/(pi*"32mm"*"3.85N/mm²")`

Calculator

LaTeX

Reset

👍

Download Bolt Loads in Gasket Joints Formulas PDF

Width of U Collar given Initial Bolt Load to Seat Gasket Joint Solution

STEP 0: Pre-Calculation Summary

Formula Used

Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load)
b = W_m2/(pi*G*y_sl)
This formula uses 1 Constants, 4 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Width of u-collar - (Measured in Meter) - Width of u-collar is definied as the measurement or extent of u-collar from side to side.
Initial bolt load to seat the gasket joint - (Measured in Newton) - Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length.
Gasket Diameter - (Measured in Meter) - Gasket Diameter is a straight line passing from side to side through the centre of a gasket.
Gasket Unit Seating Load - (Measured in Pascal) - Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.

STEP 1: Convert Input(s) to Base Unit

Initial bolt load to seat the gasket joint: 1605 Newton --> 1605 Newton No Conversion Required
Gasket Diameter: 32 Millimeter --> 0.032 Meter (Check conversion here)
Gasket Unit Seating Load: 3.85 Newton per Square Millimeter --> 3850000 Pascal (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

b = W_m2/(pi*G*y_sl) --> 1605/(pi*0.032*3850000)

Evaluating ... ...

b = 0.00414681304646903

STEP 3: Convert Result to Output's Unit

0.00414681304646903 Meter -->4.14681304646903 Millimeter (Check conversion here)

FINAL ANSWER

4.14681304646903 ≈ 4.146813 Millimeter <-- Width of u-collar

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Packing » Bolt Loads in Gasket Joints » Width of U Collar given Initial Bolt Load to Seat Gasket Joint

Credits

Created by sanjay shiva

national institute of technology hamirpur (NITH ), hamirpur , himachal pradesh

sanjay shiva has created this Calculator and 100+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< 16 Bolt Loads in Gasket Joints Calculators

Bolt Load under operating condition given Hydrostatic End Force

Go Bolt Load Under Operating Condition for Gasket = ((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)+(2*Width of u-collar*pi*Gasket Diameter*Pressure at Outer Diameter of Gasket*Gasket Factor)

Hydrostatic End Force given Bolt Load under Operating condition

Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-(2*Width of u-collar*pi*Gasket Diameter*Gasket Factor*Pressure at Outer Diameter of Gasket)

Hydrostatic Contact Force given Bolt Load under Operating condition

Go Total Joint Surface Compression Load = Bolt Load Under Operating Condition for Gasket-((pi/4)*(Gasket Diameter)^2*Pressure at Outer Diameter of Gasket)

Actual Cross-sectional Area of Bolts given Root Diameter of Thread

Go Actual Bolt Area = (2*pi*Gasket Unit Seating Load*Gasket Diameter*Gasket Width)/(Stress Required for Gasket Seating)

Gasket Width given actual Cross-sectional Area of Bolts

Go Gasket Width = (Stress Required for Gasket Seating*Actual Bolt Area)/(2*pi*Gasket Unit Seating Load*Gasket Diameter)

Stress Required for Gasket Seating

Go Stress Required for Gasket Seating = (2*pi*Gasket Unit Seating Load*Gasket Diameter*Gasket Width)/(Actual Bolt Area)

Stress Required for Gasket Seating given Bolt Load

Go Stress Required for Gasket Seating = Bolt Load Under Operating Condition for Gasket/((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)

Bolt Load in Design of Flange for Gasket Seating

Go Bolt Load Under Operating Condition for Gasket = ((Greater Cross-section Area of Bolts+Actual Bolt Area)/2)*Stress Required for Gasket Seating

Width of U Collar given Initial Bolt Load to Seat Gasket Joint

Go Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load)

Deflection of Spring Initial Bolt Load to Seal Gasket Joint

Go Gasket Unit Seating Load = Initial bolt load to seat the gasket joint/(pi*Width of u-collar*Gasket Diameter)

Initial Bolt Load to seat Gasket Joint

Go Initial bolt load to seat the gasket joint = pi*Width of u-collar*Gasket Diameter*Gasket Unit Seating Load

Test pressure given Bolt Load

Go Test Pressure in Bolted Gasket Joint = Bolt Load in Gasket Joint/(Factor of Safety for Bolt Packing*Greater Cross-section Area of Bolts)

Load on bolts based on hydrostatic end force

Go Bolt Load in Gasket Joint = Factor of Safety for Bolt Packing*Test Pressure in Bolted Gasket Joint*Greater Cross-section Area of Bolts

Total cross-sectional area of bolt at root of thread

Go Bolt Cross-sectional Area at Root of Thread = Bolt Load Under Operating Condition for Gasket/(Stress Required for Operating Condition for Gasket)

Bolt load under operating condition

Go Bolt Load Under Operating Condition for Gasket = Hydrostatic End Force in Gasket Seal+Total Joint Surface Compression Load

Hydrostatic end force

Go Hydrostatic End Force in Gasket Seal = Bolt Load Under Operating Condition for Gasket-Total Joint Surface Compression Load

Width of U Collar given Initial Bolt Load to Seat Gasket Joint Formula

Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load)
b = W_m2/(pi*G*y_sl)

What is Width of u collar?

Width of u-collar is definied as the measurement or extent of u-collar from side to side.Si unit is m.

How to Calculate Width of U Collar given Initial Bolt Load to Seat Gasket Joint?

Width of U Collar given Initial Bolt Load to Seat Gasket Joint calculator uses Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load) to calculate the Width of u-collar, The Width of U Collar given Initial Bolt Load to Seat Gasket Joint formula is defined as the measurement or extent of the u-collar from side to side. Width of u-collar is denoted by b symbol.

How to calculate Width of U Collar given Initial Bolt Load to Seat Gasket Joint using this online calculator? To use this online calculator for Width of U Collar given Initial Bolt Load to Seat Gasket Joint, enter Initial bolt load to seat the gasket joint (W_m2), Gasket Diameter (G) & Gasket Unit Seating Load (y_sl) and hit the calculate button. Here is how the Width of U Collar given Initial Bolt Load to Seat Gasket Joint calculation can be explained with given input values -> 4146.813 = 1605/(pi*0.032*3850000).

FAQ

What is Width of U Collar given Initial Bolt Load to Seat Gasket Joint?

The Width of U Collar given Initial Bolt Load to Seat Gasket Joint formula is defined as the measurement or extent of the u-collar from side to side and is represented as b = W_m2/(pi*G*y_sl) or Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load). Initial bolt load to seat the gasket joint contact surface is defined as load in terms of either a concentrated force or a prescribed change in length, Gasket Diameter is a straight line passing from side to side through the centre of a gasket & Gasket Unit Seating Load is the seating load on per unit area o the sealing gasket.

How to calculate Width of U Collar given Initial Bolt Load to Seat Gasket Joint?

The Width of U Collar given Initial Bolt Load to Seat Gasket Joint formula is defined as the measurement or extent of the u-collar from side to side is calculated using Width of u-collar = Initial bolt load to seat the gasket joint/(pi*Gasket Diameter*Gasket Unit Seating Load). To calculate Width of U Collar given Initial Bolt Load to Seat Gasket Joint, you need Initial bolt load to seat the gasket joint (W_m2), Gasket Diameter (G) & Gasket Unit Seating Load (y_sl). With our tool, you need to enter the respective value for Initial bolt load to seat the gasket joint, Gasket Diameter & Gasket Unit Seating Load and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search