Adjusted Design Value for Withdrawal for Wood Screws Calculator

✖Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.ⓘ Nominal Design Value for Withdrawal [W]			+10% -10%
✖Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.ⓘ Load Duration Factor [C_D]			+10% -10%
✖Wet Service Factor is used to signify wood that will not be used in a dry condition.ⓘ Wet Service Factor [C_m]			+10% -10%
✖Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.ⓘ Temperature Factor [C_t]			+10% -10%

✖Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.ⓘ Adjusted Design Value for Withdrawal for Wood Screws [W']

⎘ Copy

👎

Formula

✖

Adjusted Design Value for Withdrawal for Wood Screws

Formula

`"W'" = "W"*"C"_{"D"}*"C"_{"m"}*"C"_{"t"}`

Example

`"23.976N"="50N"*"0.74"*"0.81"*"0.8"`

Calculator

LaTeX

Reset

👍

Download Timber Engineering Formula PDF

Adjusted Design Value for Withdrawal for Wood Screws Solution

STEP 0: Pre-Calculation Summary

Formula Used

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor
W' = W*C_D*C_m*C_t
This formula uses 5 Variables

Variables Used

Adjusted Design Value for Withdrawal - (Measured in Newton) - Adjusted design value for withdrawal is given in terms of nominal design values and adjustment factors.
Nominal Design Value for Withdrawal - (Measured in Newton) - Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures.
Load Duration Factor - Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time.
Wet Service Factor - Wet Service Factor is used to signify wood that will not be used in a dry condition.
Temperature Factor - Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.

STEP 1: Convert Input(s) to Base Unit

Nominal Design Value for Withdrawal: 50 Newton --> 50 Newton No Conversion Required
Load Duration Factor: 0.74 --> No Conversion Required
Wet Service Factor: 0.81 --> No Conversion Required
Temperature Factor: 0.8 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

W' = W*C_D*C_m*C_t --> 50*0.74*0.81*0.8

Evaluating ... ...

W' = 23.976

STEP 3: Convert Result to Output's Unit

23.976 Newton --> No Conversion Required

FINAL ANSWER

23.976 Newton <-- Adjusted Design Value for Withdrawal

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Timber Engineering » Adjustment of Design Values for Connections with Fasteners » Adjusted Design Value for Withdrawal for Wood Screws

Credits

Created by Chandana P Dev

NSS College of Engineering (NSSCE), Palakkad

Chandana P Dev has created this Calculator and 500+ more calculators!

Verified by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has verified this Calculator and 700+ more calculators!

< 13 Adjustment of Design Values for Connections with Fasteners Calculators

Adjusted Value for Loading Parallel to Grain for Split Ring and Shear Plate Connectors

Go Adjusted Value for Loading Perpendicular to Grain = Nominal Design Value for Loading Parallel to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor*Metal Side-Plate Factor

Adjusted Design Value for Lateral Loading for Drift Bolts and Pins

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Penetration Depth Factor*Geometry Factor*End Grain Factor

Adjusted Design Value for Lateral Loading for Lag Screws

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Wet Service Factor*Load Duration Factor*Temperature Factor*Penetration Depth Factor*End Grain Factor*Group Action Factor*Geometry Factor

Adjusted Design Value for Lateral Loading for Nails and Spikes

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor*Penetration Depth Factor*Diaphragm Factor*Toenail Factor

Adjusted Value for Loading Normal to Grain for Split Ring and Shear Plate Connectors

Go Adjusted Value for Loading Normal to Grain = Nominal Design Value for Loading Normal to Grain*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor*Penetration Depth Factor

Adjusted Design Value for Lateral Loading for Bolts

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor for Bolts*Wet Service Factor*Temperature Factor*Group Action Factor*Geometry Factor

Adjusted Design Value for Lateral Loading for Wood Screws

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor*Penetration Depth Factor

Adjusted Design Value for Lateral Loading for Spike Grids

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor*Wet Service Factor*Temperature Factor*Geometry Factor

Adjusted Design Value for Withdrawal for Drift Bolts and Pins

Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor

Adjusted Design Value for Withdrawal for Lag Screws

Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor

Adjusted Design Value for Withdrawal for Nails and Spikes

Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor

Adjusted Design Value for Lateral Loading for Metal Plate Connectors

Go Adjusted Design Value for Lateral Loading = Nominal Design Value for Lateral Loading*Load Duration Factor*Wet Service Factor*Temperature Factor

Adjusted Design Value for Withdrawal for Wood Screws

Go Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor

Adjusted Design Value for Withdrawal for Wood Screws Formula

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor
W' = W*C_D*C_m*C_t

What are Wood Screws?

A metal screw with a sharp point is designed to attach two pieces of wood together. Wood screws are commonly available with flat, pan or oval heads. A wood screw generally has a partially unthreaded shank below the head.

What is Adjusted Design Value for Withdrawal?

Nominal design values for laterally loaded fasteners Z, withdrawal of fasteners W, load parallel to grain P, and load perpendicular to grain Q should be multiplied by applicable adjustment factors to determine adjusted design values. The load applied to a connection should not exceed the adjusted design value.

How to Calculate Adjusted Design Value for Withdrawal for Wood Screws?

Adjusted Design Value for Withdrawal for Wood Screws calculator uses Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor to calculate the Adjusted Design Value for Withdrawal, Adjusted Design Value for Withdrawal for Wood Screws is defined by the parameters, say, nominal design value for withdrawal, wet service factor, load duration factor and temperature factor. Adjusted Design Value for Withdrawal is denoted by W' symbol.

How to calculate Adjusted Design Value for Withdrawal for Wood Screws using this online calculator? To use this online calculator for Adjusted Design Value for Withdrawal for Wood Screws, enter Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m) & Temperature Factor (C_t) and hit the calculate button. Here is how the Adjusted Design Value for Withdrawal for Wood Screws calculation can be explained with given input values -> 23.976 = 50*0.74*0.81*0.8.

FAQ

What is Adjusted Design Value for Withdrawal for Wood Screws?

Adjusted Design Value for Withdrawal for Wood Screws is defined by the parameters, say, nominal design value for withdrawal, wet service factor, load duration factor and temperature factor and is represented as W' = W*C_D*C_m*C_t or Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor. Nominal Design Value for Withdrawal is the load acting on the fasteners in timber structures, Load Duration Factor is based on the ability of wood to recover after a reasonable load has been applied for a given time, Wet Service Factor is used to signify wood that will not be used in a dry condition & Temperature factor is the factor used for wood that is expected to be exposed to high temperatures for long periods of time.

How to calculate Adjusted Design Value for Withdrawal for Wood Screws?

Adjusted Design Value for Withdrawal for Wood Screws is defined by the parameters, say, nominal design value for withdrawal, wet service factor, load duration factor and temperature factor is calculated using Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor. To calculate Adjusted Design Value for Withdrawal for Wood Screws, you need Nominal Design Value for Withdrawal (W), Load Duration Factor (C_D), Wet Service Factor (C_m) & Temperature Factor (C_t). With our tool, you need to enter the respective value for Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor & Temperature Factor and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Adjusted Design Value for Withdrawal?

In this formula, Adjusted Design Value for Withdrawal uses Nominal Design Value for Withdrawal, Load Duration Factor, Wet Service Factor & Temperature Factor. We can use 3 other way(s) to calculate the same, which is/are as follows -

Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*Toenail Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*End Grain Factor*Temperature Factor
Adjusted Design Value for Withdrawal = Nominal Design Value for Withdrawal*Load Duration Factor*Wet Service Factor*Temperature Factor*End Grain Factor

Home

FREE PDFs

🔍 Search