Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load Calculator

✖Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit.ⓘ Peak Input Voltage SP [V_(max)]			+10% -10%
✖Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.ⓘ Resistance SP [r]			+10% -10%

✖Average Output Current Full is the average of the dc value of the output current.ⓘ Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load [I_avg(f)]

⎘ Copy

👎

Formula

✖

Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Formula

`"I"_{"avg(f)"} = (2*"V"_{"(max)"})/(pi*"r")`

Example

`"2.384627A"=(2*"221V")/(pi*"59Ω")`

Calculator

LaTeX

Reset

👍

Download Single Phase Uncontrolled Rectifiers Formulas PDF

Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load Solution

STEP 0: Pre-Calculation Summary

Formula Used

Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP)
I_avg(f) = (2*V_(max))/(pi*r)
This formula uses 1 Constants, 3 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Average Output Current Full - (Measured in Ampere) - Average Output Current Full is the average of the dc value of the output current.
Peak Input Voltage SP - (Measured in Volt) - Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit.
Resistance SP - (Measured in Ohm) - Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.

STEP 1: Convert Input(s) to Base Unit

Peak Input Voltage SP: 221 Volt --> 221 Volt No Conversion Required
Resistance SP: 59 Ohm --> 59 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_avg(f) = (2*V_(max))/(pi*r) --> (2*221)/(pi*59)

Evaluating ... ...

I_avg(f) = 2.38462660497009

STEP 3: Convert Result to Output's Unit

2.38462660497009 Ampere --> No Conversion Required

FINAL ANSWER

2.38462660497009 ≈ 2.384627 Ampere <-- Average Output Current Full

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power Electronics » Uncontrolled Rectifiers » Single Phase Uncontrolled Rectifiers » Full Wave » Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Credits

Created by Parminder Singh

Chandigarh University (CU), Punjab

Parminder Singh has created this Calculator and 100+ more calculators!

Verified by Rachita C

BMS College Of Engineering (BMSCE), Banglore

Rachita C has verified this Calculator and 50+ more calculators!

< 6 Full Wave Calculators

Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP)

Output Average Power of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go Average Output Power SP = (2/pi)^2*Peak Input Voltage SP*Peak Load Current

Average Output Voltage of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go Average Output Voltage Full = (2*Peak Input Voltage SP)/pi

RMS Output Voltage of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go RMS Output Voltage Full = Peak Input Voltage SP/sqrt(2)

RMS Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go RMS Output Current = Source Voltage/Resistance SP

Ripple Voltage of Single Phase Full Wave Midpoint Diode Rectifier with R Load

Go Ripple Voltage Full = 0.3077*Peak Input Voltage SP

Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load Formula

Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP)
I_avg(f) = (2*V_(max))/(pi*r)

What is full wave rectifier?

A full wave rectifier is a device that converts the whole of input ac voltage into dc output voltage. A full wave rectifier converts both positive half and negative half of the ac input cycle unlike half wave rectifier. A full wave rectifier uses two diodes connected in opposite orientation so either one of them can be forward biased for positive and negative half of input ac cycle.

How to Calculate Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load?

Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load calculator uses Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP) to calculate the Average Output Current Full, The Average output current of single phase full wave midpoint diode rectifier with R load formula is defined as the average value of the output current over a complete input cycle when the load is resistive in nature. Average Output Current Full is denoted by I_avg(f) symbol.

How to calculate Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load using this online calculator? To use this online calculator for Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load, enter Peak Input Voltage SP (V_(max)) & Resistance SP (r) and hit the calculate button. Here is how the Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load calculation can be explained with given input values -> 2.384627 = (2*221)/(pi*59).

FAQ

What is Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load?

The Average output current of single phase full wave midpoint diode rectifier with R load formula is defined as the average value of the output current over a complete input cycle when the load is resistive in nature and is represented as I_avg(f) = (2*V_(max))/(pi*r) or Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP). Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit & Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.

How to calculate Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load?

The Average output current of single phase full wave midpoint diode rectifier with R load formula is defined as the average value of the output current over a complete input cycle when the load is resistive in nature is calculated using Average Output Current Full = (2*Peak Input Voltage SP)/(pi*Resistance SP). To calculate Average Output Current of Single Phase Full Wave Midpoint Diode Rectifier with R Load, you need Peak Input Voltage SP (V_(max)) & Resistance SP (r). With our tool, you need to enter the respective value for Peak Input Voltage SP & Resistance SP and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search