Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode Calculator

✖Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit.ⓘ Peak Input Voltage SP [V_(max)]			+10% -10%
✖Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.ⓘ Resistance SP [r]			+10% -10%

✖Average Output Current Half is the average of the dc value of the output current.ⓘ Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode [I_avg(h)]

⎘ Copy

👎

Formula

✖

Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode

Formula

`"I"_{"avg(h)"} = "V"_{"(max)"}/(pi*"r")`

Example

`"1.192313A"="221V"/(pi*"59Ω")`

Calculator

LaTeX

Reset

👍

Download Single Phase Uncontrolled Rectifiers Formulas PDF PDF Image

Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode Solution

STEP 0: Pre-Calculation Summary

Formula Used

Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP)
I_avg(h) = V_(max)/(pi*r)
This formula uses 1 Constants, 3 Variables

Constants Used

pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288

Variables Used

Average Output Current Half - (Measured in Ampere) - Average Output Current Half is the average of the dc value of the output current.
Peak Input Voltage SP - (Measured in Volt) - Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit.
Resistance SP - (Measured in Ohm) - Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.

STEP 1: Convert Input(s) to Base Unit

Peak Input Voltage SP: 221 Volt --> 221 Volt No Conversion Required
Resistance SP: 59 Ohm --> 59 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

I_avg(h) = V_(max)/(pi*r) --> 221/(pi*59)

Evaluating ... ...

I_avg(h) = 1.19231330248505

STEP 3: Convert Result to Output's Unit

1.19231330248505 Ampere --> No Conversion Required

FINAL ANSWER

1.19231330248505 ≈ 1.192313 Ampere <-- Average Output Current Half

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Power Electronics » Uncontrolled Rectifiers » Single Phase Uncontrolled Rectifiers » Half Wave » Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode

Credits

Created by Parminder Singh

Chandigarh University (CU), Punjab

Parminder Singh has created this Calculator and 100+ more calculators!

Verified by Rachita C

BMS College Of Engineering (BMSCE), Banglore

Rachita C has verified this Calculator and 50+ more calculators!

< 13 Half Wave Calculators

RMS Load Current of Single Phase Half Wave Diode Rectifier with RE Load

Go RMS Load Current SP = sqrt(((Source Voltage^2+Load EMF^2)*(pi-(2*Diode Turn On Angle Radians))+Source Voltage^2*sin(2*Diode Turn On Angle Degrees)-4*Peak Input Voltage SP*Load EMF*cos(Diode Turn On Angle Degrees))/(2*pi*Resistance SP^2))

Average Output Current of Single Phase Half Wave Diode Rectifier with Resistive and Inductive Load

Go Average Output Current Half = (Peak Input Voltage SP/(2*pi*Resistance SP))/(1-cos(Diode Extinction Angle))

Average Output Voltage of Single Phase Half Wave Diode Rectifier with RL Load

Go Average Output Voltage Half = (Peak Input Voltage SP/(2*pi))*(1-cos(Diode Extinction Angle))

Average Load Current of Single Phase Half Wave Diode Rectifier with Inductive Load

Go Average Load Current SP = Peak Input Voltage SP/(Angular Frequency*Inductance)

Peak Load Current in Single Phase Half Wave Diode Rectifier with Inductive Load

Go Peak Load Current = (2*Peak Input Voltage SP)/(Angular Frequency*Inductance)

Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode

Go Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP)

Average Load Current of Single Phase Half Wave Diode Rectifier with Resistive Load

Go Average Load Current SP = Peak Input Voltage SP/(pi*Resistance SP)

Output DC Power of Single-Phase Half Wave Diode Rectifier with R Load

Go DC Power Output SP = (Peak Input Voltage SP*Peak Load Current)/pi^2

RMS Load Current of Single Phase Half Wave Diode Rectifier with Resistive Load

Go RMS Load Current SP = Peak Input Voltage SP/(2*Resistance SP)

Average Output Voltage of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode

Go Average Output Voltage Half = Peak Input Voltage SP/pi

Average Output Voltage of Single Phase Half Wave Diode Rectifier with Resistive Load

Go Average Output Voltage Half = Peak Input Voltage SP/pi

Ripple Voltage of Single-Phase Half Wave Diode Rectifier with R Load

Go Ripple Voltage Half = 0.3856*Peak Input Voltage SP

RMS Output Voltage of Single Phase Half Wave Diode Rectifier with Resistive Load

Go RMS Output Voltage Half = Peak Input Voltage SP/2

Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode Formula

Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP)
I_avg(h) = V_(max)/(pi*r)

What is Conduction time for freewheeling diode?

Freewheeling diode is use in order to dissipate the energy stored in inductor during the positive half of input from it. So it conducts when the inductor starts discharging during the negative half of the cycle and it conducts until the extinction angle of the diode which is usually between 90 to 120 radians.

How to Calculate Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode?

Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode calculator uses Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP) to calculate the Average Output Current Half, The Average output current of single phase half wave diode rectifier with RL load and freewheeling diode formula is defined as the average of current on the output side of a rectifier over a complete cycle when the load is resistive and inductive in nature and a freewheeling diode is employed in the circuit. Average Output Current Half is denoted by I_avg(h) symbol.

How to calculate Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode using this online calculator? To use this online calculator for Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode, enter Peak Input Voltage SP (V_(max)) & Resistance SP (r) and hit the calculate button. Here is how the Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode calculation can be explained with given input values -> 1.192313 = 221/(pi*59).

FAQ

What is Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode?

The Average output current of single phase half wave diode rectifier with RL load and freewheeling diode formula is defined as the average of current on the output side of a rectifier over a complete cycle when the load is resistive and inductive in nature and a freewheeling diode is employed in the circuit and is represented as I_avg(h) = V_(max)/(pi*r) or Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP). Peak Input Voltage SP is the peak of the alternating voltage provided at the input of any electrical circuit & Resistance SP is a measure of the opposition to current flow in an electrical circuit. Its S.I unit is ohm.

How to calculate Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode?

The Average output current of single phase half wave diode rectifier with RL load and freewheeling diode formula is defined as the average of current on the output side of a rectifier over a complete cycle when the load is resistive and inductive in nature and a freewheeling diode is employed in the circuit is calculated using Average Output Current Half = Peak Input Voltage SP/(pi*Resistance SP). To calculate Average Output Current of Single Phase Half Wave Diode Rectifier with RL Load and Freewheeling Diode, you need Peak Input Voltage SP (V_(max)) & Resistance SP (r). With our tool, you need to enter the respective value for Peak Input Voltage SP & Resistance SP and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Average Output Current Half?

In this formula, Average Output Current Half uses Peak Input Voltage SP & Resistance SP. We can use 1 other way(s) to calculate the same, which is/are as follows -

Average Output Current Half = (Peak Input Voltage SP/(2*pi*Resistance SP))/(1-cos(Diode Extinction Angle))

Home

FREE PDFs

🔍 Search