CFA RF Power Output Calculator

↳

Electronics

Chemical Engineering

Civil

Electrical

Electronics and Instrumentation

Materials Science

Mechanical

Production Engineering

⤿

Special Purpose Radars

Radar & Antenna Specifications

Radar Antennas Reception

✖Efficiency of Cross Field Amplifier refers to the ratio of output power to input power in the device. CFAs are vacuum tube devices used to amplify high-frequency radio-frequency (RF) signals.ⓘ Efficiency of Cross Field Amplifier [η_cfa]			+10% -10%
✖DC Power Input is the power input through direct current supply.ⓘ DC Power Input [P_dc]			+10% -10%
✖CFA RF Drive Power refers to the radio frequency (RF) power that is applied to the input of the CFA which is usually a weak signal that needs amplification to reach a higher power.ⓘ CFA RF Drive Power [P_drive]			+10% -10%

✖CFA RF Power Output which is also known as transmitter power output (TPO) is the actual amount of power of radio frequency (RF) energy that a transmitter produces at its output.ⓘ CFA RF Power Output [P_out]

⎘ Copy

👎

Formula

✖

CFA RF Power Output

Formula

`"P"_{"out"} = "η"_{"cfa"}*"P"_{"dc"}+"P"_{"drive"}`

Example

`"96.46W"="0.98"*"27W"+"70W"`

Calculator

LaTeX

Reset

👍

Download Special Purpose Radars Formulas PDF PDF Image

CFA RF Power Output Solution

STEP 0: Pre-Calculation Summary

Formula Used

CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power
P_out = η_cfa*P_dc+P_drive
This formula uses 4 Variables

Variables Used

CFA RF Power Output - (Measured in Watt) - CFA RF Power Output which is also known as transmitter power output (TPO) is the actual amount of power of radio frequency (RF) energy that a transmitter produces at its output.
Efficiency of Cross Field Amplifier - Efficiency of Cross Field Amplifier refers to the ratio of output power to input power in the device. CFAs are vacuum tube devices used to amplify high-frequency radio-frequency (RF) signals.
DC Power Input - (Measured in Watt) - DC Power Input is the power input through direct current supply.
CFA RF Drive Power - (Measured in Watt) - CFA RF Drive Power refers to the radio frequency (RF) power that is applied to the input of the CFA which is usually a weak signal that needs amplification to reach a higher power.

STEP 1: Convert Input(s) to Base Unit

Efficiency of Cross Field Amplifier: 0.98 --> No Conversion Required
DC Power Input: 27 Watt --> 27 Watt No Conversion Required
CFA RF Drive Power: 70 Watt --> 70 Watt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

P_out = η_cfa*P_dc+P_drive --> 0.98*27+70

Evaluating ... ...

P_out = 96.46

STEP 3: Convert Result to Output's Unit

96.46 Watt --> No Conversion Required

FINAL ANSWER

96.46 Watt <-- CFA RF Power Output

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » Radar System » Special Purpose Radars » CFA RF Power Output

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< 21 Special Purpose Radars Calculators

Amplitude of Signal Received from Target at Range

Go Amplitude of Signal Received = Echo Signal Voltage/(sin((2*pi*(Carrier Frequency+Doppler Frequency Shift)*Time Period)-((4*pi*Carrier Frequency*Range)/[c])))

Echo Signal Voltage

Go Echo Signal Voltage = Amplitude of Signal Received*sin((2*pi*(Carrier Frequency+Doppler Frequency Shift)*Time Period)-((4*pi*Carrier Frequency*Range)/[c]))

Velocity Smoothing Parameter

Go Velocity Smoothing Parameter = ((Smoothed Velocity-(n-1)th Scan Smoothed Velocity)/(Measured Position at Nth Scan-Target Predicted Position))*Time between Observations

Time between Observations

Go Time between Observations = (Velocity Smoothing Parameter/(Smoothed Velocity-(n-1)th Scan Smoothed Velocity))*(Measured Position at Nth Scan-Target Predicted Position)

Smoothed Velocity

Go Smoothed Velocity = (n-1)th Scan Smoothed Velocity+Velocity Smoothing Parameter/Time between Observations*(Measured Position at Nth Scan-Target Predicted Position)

Phase Difference between Echo Signals in Monopulse Radar

Go Phase Difference between Echo Signals = 2*pi*Distance between Antennas in Monopulse Radar*sin(Angle in Monopulse Radar)/Wavelength

Predicted Position of Target

Go Target Predicted Position = (Smoothed Position-(Position Smoothing Parameter*Measured Position at Nth Scan))/(1-Position Smoothing Parameter)

Amplitude of Reference Signal

Go Amplitude of Reference Signal = CW Oscillator Reference Voltage/(sin(2*pi*Angular Frequency*Time Period))

Reference Voltage of CW Oscillator

Go CW Oscillator Reference Voltage = Amplitude of Reference Signal*sin(2*pi*Angular Frequency*Time Period)

Measured Position at Nth Scan

Go Measured Position at Nth Scan = ((Smoothed Position-Target Predicted Position)/Position Smoothing Parameter)+Target Predicted Position

Position Smoothing Parameter

Go Position Smoothing Parameter = (Smoothed Position-Target Predicted Position)/(Measured Position at Nth Scan-Target Predicted Position)

Smoothed Position

Go Smoothed Position = Target Predicted Position+Position Smoothing Parameter*(Measured Position at Nth Scan-Target Predicted Position)

Distance from Antenna 1 to Target in Monopulse Radar

Go Distance from Antenna 1 to Target = (Range+Distance between Antennas in Monopulse Radar)/2*sin(Angle in Monopulse Radar)

Distance from Antenna 2 to Target in Monopulse Radar

Go Distance from Antenna 2 to Target = (Range-Distance between Antennas in Monopulse Radar)/2*sin(Angle in Monopulse Radar)

Efficiency of Cross Field Amplifier(CFA)

Go Efficiency of Cross Field Amplifier = (CFA RF Power Output-CFA RF Drive Power)/DC Power Input

CFA DC Power Input

Go DC Power Input = (CFA RF Power Output-CFA RF Drive Power)/Efficiency of Cross Field Amplifier

CFA RF Power Output

Go CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power

CFA RF Drive Power

Go CFA RF Drive Power = CFA RF Power Output-Efficiency of Cross Field Amplifier*DC Power Input

Range Resolution

Go Range Resolution = (2*Antenna Height*Target Height)/Range

Doppler Frequency Shift

Go Doppler Frequency Shift = (2*Target Velocity)/Wavelength

Peak Quantization Lobe

Go Peak Quantization Lobe = 1/2^(2*Mean Lobe)

CFA RF Power Output Formula

CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power
P_out = η_cfa*P_dc+P_drive

What is Max RF power?

The maximum RF power allowed in a IIC hazardous area is 2W (2000mW), so in this example the RF power level is well below the safe level specified in the standards and, therefore, safe to use in the IIC hazardous area.

How to Calculate CFA RF Power Output?

CFA RF Power Output calculator uses CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power to calculate the CFA RF Power Output, The CFA RF Power Output formula is defined as in radio transmission, transmitter power output (TPO) is the actual amount of power (in watts) of radio frequency (RF) energy that a transmitter produces at its output. CFA RF Power Output is denoted by P_out symbol.

How to calculate CFA RF Power Output using this online calculator? To use this online calculator for CFA RF Power Output, enter Efficiency of Cross Field Amplifier (η_cfa), DC Power Input (P_dc) & CFA RF Drive Power (P_drive) and hit the calculate button. Here is how the CFA RF Power Output calculation can be explained with given input values -> 96.46 = 0.98*27+70.

FAQ

What is CFA RF Power Output?

The CFA RF Power Output formula is defined as in radio transmission, transmitter power output (TPO) is the actual amount of power (in watts) of radio frequency (RF) energy that a transmitter produces at its output and is represented as P_out = η_cfa*P_dc+P_drive or CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power. Efficiency of Cross Field Amplifier refers to the ratio of output power to input power in the device. CFAs are vacuum tube devices used to amplify high-frequency radio-frequency (RF) signals, DC Power Input is the power input through direct current supply & CFA RF Drive Power refers to the radio frequency (RF) power that is applied to the input of the CFA which is usually a weak signal that needs amplification to reach a higher power.

How to calculate CFA RF Power Output?

The CFA RF Power Output formula is defined as in radio transmission, transmitter power output (TPO) is the actual amount of power (in watts) of radio frequency (RF) energy that a transmitter produces at its output is calculated using CFA RF Power Output = Efficiency of Cross Field Amplifier*DC Power Input+CFA RF Drive Power. To calculate CFA RF Power Output, you need Efficiency of Cross Field Amplifier (η_cfa), DC Power Input (P_dc) & CFA RF Drive Power (P_drive). With our tool, you need to enter the respective value for Efficiency of Cross Field Amplifier, DC Power Input & CFA RF Drive Power and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search