Diameter of rivet given strength of joint per pitch length (double rivet) Calculator

✖Strength of joint is the strength of riveted joint per pitch length.ⓘ Strength of joint [S]			+10% -10%
✖Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.ⓘ Crushing stress [σ_c]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Diameter of rivet given strength of joint per pitch length (double rivet) [D_rivet]

⎘ Copy

👎

Formula

✖

Diameter of rivet given strength of joint per pitch length (double rivet)

Formula

`"D"_{"rivet"} = "S"/(2*"σ"_{"c"}*"t"_{"plate"})`

Example

`"149.3056mm"="8.6kN"/(2*"2.4MPa"*"12mm")`

Calculator

LaTeX

Reset

👍

Download Strength of Materials Formula PDF

Diameter of rivet given strength of joint per pitch length (double rivet) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate)
D_rivet = S/(2*σ_c*t_plate)
This formula uses 4 Variables

Variables Used

Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.
Strength of joint - (Measured in Newton) - Strength of joint is the strength of riveted joint per pitch length.
Crushing stress - (Measured in Pascal) - Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Strength of joint: 8.6 Kilonewton --> 8600 Newton (Check conversion here)
Crushing stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

D_rivet = S/(2*σ_c*t_plate) --> 8600/(2*2400000*0.012)

Evaluating ... ...

D_rivet = 0.149305555555556

STEP 3: Convert Result to Output's Unit

0.149305555555556 Meter -->149.305555555556 Millimeter (Check conversion here)

FINAL ANSWER

149.305555555556 ≈ 149.3056 Millimeter <-- Rivet Diameter

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Failure Of A Riveted Joint » Failure Due To Crushing Of Rivet Or Plate » Diameter of rivet given strength of joint per pitch length (double rivet)

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< 24 Failure Due To Crushing Of Rivet Or Plate Calculators

Allowable crushing stress given strength of joint per pitch length of joint against crushing

Go Crushing stress = Strength of joint/(Number of Rivets Per Pitch*Rivet Diameter*Thickness of Plate)

Thickness of plates given strength of joint per pitch length of joint against crushing

Go Thickness of Plate = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)

Diameter of rivet given strength of joint per pitch length of joint against crushing

Go Rivet Diameter = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Thickness of Plate)

Number of rivets given strength of joint per pitch length of joint against crushing

Go Number of Rivets Per Pitch = Strength of joint/(Crushing stress*Rivet Diameter*Thickness of Plate)

Strength of joint per pitch length of joint against crushing

Go Strength of joint = (Number of Rivets Per Pitch*Crushing stress*Rivet Diameter*Thickness of Plate)

Allowable crushing stress given strength of joint per pitch length (single rivet)

Go Crushing stress = Strength of joint/(1*Rivet Diameter*Thickness of Plate)

Allowable crushing stress given strength of joint per pitch length (double rivet)

Go Crushing stress = Strength of joint/(2*Rivet Diameter*Thickness of Plate)

Allowable crushing stress given strength of joint per pitch length (triple rivet)

Go Crushing stress = Strength of joint/(3*Rivet Diameter*Thickness of Plate)

Thickness of plates given strength of joint per pitch length (single rivet)

Go Thickness of Plate = Strength of joint/(1*Crushing stress*Rivet Diameter)

Thickness of plates given strength of joint per pitch length (double rivet)

Go Thickness of Plate = Strength of joint/(2*Crushing stress*Rivet Diameter)

Strength of joint per pitch length of joint against crushing (triple rivet)

Go Strength of joint = (3*Crushing stress*Rivet Diameter*Thickness of Plate)

Thickness of plates given strength of joint per pitch length (triple rivet)

Go Thickness of Plate = Strength of joint/(3*Crushing stress*Rivet Diameter)

Strength of joint per pitch length of joint against crushing(single rivet)

Go Strength of joint = (1*Crushing stress*Rivet Diameter*Thickness of Plate)

Strength of joint per pitch length of joint against crushing(double rivet)

Go Strength of joint = (2*Crushing stress*Rivet Diameter*Thickness of Plate)

Diameter of rivet given strength of joint per pitch length (single rivet)

Go Rivet Diameter = Strength of joint/(1*Crushing stress*Thickness of Plate)

Diameter of rivet given strength of joint per pitch length (double rivet)

Go Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate)

Diameter of rivet given strength of joint per pitch length (triple-rivet)

Go Rivet Diameter = Strength of joint/(3*Crushing stress*Thickness of Plate)

Allowable crushing stress given safe load which rivet can withstand against crushing

Go Crushing stress = Safe load Joint/(Rivet Diameter*Thickness of Plate)

Thickness of plates given safe load which rivet can withstand against crushing

Go Thickness of Plate = Safe load Joint/(Crushing stress*Rivet Diameter)

Diameter of rivet given safe load that rivet can withstand against crushing

Go Rivet Diameter = Safe load Joint/(Crushing stress*Thickness of Plate)

Safe load which rivet can withstand against crushing

Go Safe load Joint = Crushing stress*Rivet Diameter*Thickness of Plate

Allowable crushing stress given safe load which rivet can withstand for given projected area

Go Crushing stress = Safe load Joint/(Projected area)

Projected area given safe load which rivet can withstand against crushing

Go Projected area = Safe load Joint/(Crushing stress)

Safe load which rivet can withstand against crushing given projected area

Go Safe load Joint = Crushing stress*Projected area

Diameter of rivet given strength of joint per pitch length (double rivet) Formula

Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate)
D_rivet = S/(2*σ_c*t_plate)

What is tear and tensile strength?

Tear strength is the measure of how much tensile stress the material can withstand in a specific case, i.e. when a tear has been introduced in the material, whereas a normal tensile stress test is done for a non-defective piece of material.

How to Calculate Diameter of rivet given strength of joint per pitch length (double rivet)?

Diameter of rivet given strength of joint per pitch length (double rivet) calculator uses Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate) to calculate the Rivet Diameter, The Diameter of rivet given strength of joint per pitch length (double rivet) formula is defined as a chord that runs through the centre point of the rivet. Rivet Diameter is denoted by D_rivet symbol.

How to calculate Diameter of rivet given strength of joint per pitch length (double rivet) using this online calculator? To use this online calculator for Diameter of rivet given strength of joint per pitch length (double rivet), enter Strength of joint (S), Crushing stress (σ_c) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Diameter of rivet given strength of joint per pitch length (double rivet) calculation can be explained with given input values -> 149305.6 = 8600/(2*2400000*0.012).

FAQ

What is Diameter of rivet given strength of joint per pitch length (double rivet)?

The Diameter of rivet given strength of joint per pitch length (double rivet) formula is defined as a chord that runs through the centre point of the rivet and is represented as D_rivet = S/(2*σ_c*t_plate) or Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate). Strength of joint is the strength of riveted joint per pitch length, Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Diameter of rivet given strength of joint per pitch length (double rivet)?

The Diameter of rivet given strength of joint per pitch length (double rivet) formula is defined as a chord that runs through the centre point of the rivet is calculated using Rivet Diameter = Strength of joint/(2*Crushing stress*Thickness of Plate). To calculate Diameter of rivet given strength of joint per pitch length (double rivet), you need Strength of joint (S), Crushing stress (σ_c) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Strength of joint, Crushing stress & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Rivet Diameter?

In this formula, Rivet Diameter uses Strength of joint, Crushing stress & Thickness of Plate. We can use 4 other way(s) to calculate the same, which is/are as follows -

Rivet Diameter = Safe load Joint/(Crushing stress*Thickness of Plate)
Rivet Diameter = Strength of joint/(1*Crushing stress*Thickness of Plate)
Rivet Diameter = Strength of joint/(3*Crushing stress*Thickness of Plate)
Rivet Diameter = Strength of joint/(Number of Rivets Per Pitch*Crushing stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search