Mass Density of Steel for Lower Section of Drill String Length in Compression Calculator

✖Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.ⓘ Density of Drilling Mud [ρ_m]			+10% -10%
✖Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.ⓘ Length of Pipe Hanging in Well [L]			+10% -10%
✖Lower Section of Drill String Length that is in Compression depends on the density of the drilling mud, length of pipe in well and mass density of steel.ⓘ Lower Section of Drill String Length [L_c]			+10% -10%

✖Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.ⓘ Mass Density of Steel for Lower Section of Drill String Length in Compression [ρ_s]

⎘ Copy

👎

Formula

✖

Mass Density of Steel for Lower Section of Drill String Length in Compression

Formula

`"ρ"_{"s"} = ("ρ"_{"m"}*"L")/"L"_{"c"}`

Example

`"7757.576kg/m³"=("1440kg/m³"*"16m")/"2.97"`

Calculator

LaTeX

Reset

👍

Download Hydrostatics Formulas PDF

Mass Density of Steel for Lower Section of Drill String Length in Compression Solution

STEP 0: Pre-Calculation Summary

Formula Used

Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length
ρ_s = (ρ_m*L)/L_c
This formula uses 4 Variables

Variables Used

Mass Density of Steel - (Measured in Kilogram per Cubic Meter) - Mass Density of Steel varies based on the alloying constituents but usually ranges between 7,750 and 8,050 kg/m3.
Density of Drilling Mud - (Measured in Kilogram per Cubic Meter) - Density of Drilling Mud considering a steel drilling pipe hanging in an oil well.
Length of Pipe Hanging in Well - (Measured in Meter) - Length of Pipe Hanging in Well is essential in calculating all other values required in drilling.
Lower Section of Drill String Length - Lower Section of Drill String Length that is in Compression depends on the density of the drilling mud, length of pipe in well and mass density of steel.

STEP 1: Convert Input(s) to Base Unit

Density of Drilling Mud: 1440 Kilogram per Cubic Meter --> 1440 Kilogram per Cubic Meter No Conversion Required
Length of Pipe Hanging in Well: 16 Meter --> 16 Meter No Conversion Required
Lower Section of Drill String Length: 2.97 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

ρ_s = (ρ_m*L)/L_c --> (1440*16)/2.97

Evaluating ... ...

ρ_s = 7757.57575757576

STEP 3: Convert Result to Output's Unit

7757.57575757576 Kilogram per Cubic Meter --> No Conversion Required

FINAL ANSWER

7757.57575757576 ≈ 7757.576 Kilogram per Cubic Meter <-- Mass Density of Steel

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Coastal and Ocean Engineering » Offshore Hydromechanics » Hydrostatics » Mass Density of Steel for Lower Section of Drill String Length in Compression

Credits

Created by Mithila Muthamma PA

Coorg Institute of Technology (CIT), Coorg

Mithila Muthamma PA has created this Calculator and 2000+ more calculators!

Verified by M Naveen

National Institute of Technology (NIT), Warangal

M Naveen has verified this Calculator and 900+ more calculators!

< 18 Hydrostatics Calculators

Mass Density of Drilling Mud when Buoyant Force acts in Direction opposite to Gravity Force

Go Density of Drilling Mud = -((Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))-Mass Density of Steel))

Length of Pipe Hanging in Well given Effective Tension

Go Length of Pipe Hanging in Well = ((Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)+Coordinate measured Downward from Top))

Coordinate measured Downward from Top given Effective Tension

Go Coordinate measured Downward from Top = -(Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe)-Length of Pipe Hanging in Well)

Mass Density of Steel when Buoyant Force acts in Direction opposite to Gravity Force

Go Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)

Cross Section Area of Steel given Effective Tension

Go Cross Section Area of Steel in Pipe = Effective Tension/((Mass Density of Steel-Density of Drilling Mud)*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Effective Tension given Buoyant Force acts in Direction opposite to Gravity Force

Go Effective Tension = (Mass Density of Steel-Density of Drilling Mud)*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)

Coordinate measured Downward from Top given Tension on Vertical Drill String

Go Coordinate measured Downward from Top = -((Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))-Length of Pipe Hanging in Well)

Cross Section Area of Steel in Pipe given Tension on Vertical Drill String

Go Cross Section Area of Steel in Pipe = Tension on Vertical Drill String/(Mass Density of Steel*[g]*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Length of Pipe Hanging in Well given Tension on Vertical Drill String

Go Length of Pipe Hanging in Well = (Tension on Vertical Drill String/(Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe))+Coordinate measured Downward from Top

Mass Density of Steel for Tension on Vertical Drill String

Go Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))

Tension on Vertical Drill String

Go Tension on Vertical Drill String = Mass Density of Steel*[g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top)

Length of Pipe Hanging in Well given Vertical Force at Bottom End of Drill String

Go Length of Pipe Hanging in Well = Vertical Force at Bottom end of Drill String/(Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe)

Mass Density of Drilling Mud given Vertical Force at Bottom End of Drill String

Go Density of Drilling Mud = Vertical Force at Bottom end of Drill String/([g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well)

Vertical Force at Bottom End of Drill String

Go Vertical Force at Bottom end of Drill String = Density of Drilling Mud*[g]*Cross Section Area of Steel in Pipe*Length of Pipe Hanging in Well

Mass Density of Drilling Mud for Lower Section of Drill String Length in Compression

Go Density of Drilling Mud = (Lower Section of Drill String Length*Mass Density of Steel)/Length of Pipe Hanging in Well

Length of Pipe Hanging given Lower Section of Drill String Length in Compression

Go Length of Pipe Hanging in Well = (Lower Section of Drill String Length*Mass Density of Steel)/Density of Drilling Mud

Mass Density of Steel for Lower Section of Drill String Length in Compression

Go Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length

Lower Section of Drill String Length that is in Compression

Go Lower Section of Drill String Length = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Mass Density of Steel

Mass Density of Steel for Lower Section of Drill String Length in Compression Formula

Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length
ρ_s = (ρ_m*L)/L_c

What is Buoyancy?

Buoyancy is the force that causes objects to float. It is the force exerted on an object that is partly or wholly immersed in a fluid. Buoyancy is caused by the differences in pressure acting on opposite sides of an object immersed in a static fluid. It is also known as the buoyant force.

How to Calculate Mass Density of Steel for Lower Section of Drill String Length in Compression?

Mass Density of Steel for Lower Section of Drill String Length in Compression calculator uses Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length to calculate the Mass Density of Steel, The Mass Density of Steel for Lower Section of Drill String Length in Compression is the mass of the fluid per unit volume. The weight density w, of a fluid is the weight of the fluid per unit volume. Mass Density of Steel is denoted by ρ_s symbol.

How to calculate Mass Density of Steel for Lower Section of Drill String Length in Compression using this online calculator? To use this online calculator for Mass Density of Steel for Lower Section of Drill String Length in Compression, enter Density of Drilling Mud (ρ_m), Length of Pipe Hanging in Well (L) & Lower Section of Drill String Length (L_c) and hit the calculate button. Here is how the Mass Density of Steel for Lower Section of Drill String Length in Compression calculation can be explained with given input values -> 7757.576 = (1440*16)/2.97.

FAQ

What is Mass Density of Steel for Lower Section of Drill String Length in Compression?

The Mass Density of Steel for Lower Section of Drill String Length in Compression is the mass of the fluid per unit volume. The weight density w, of a fluid is the weight of the fluid per unit volume and is represented as ρ_s = (ρ_m*L)/L_c or Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length. Density of Drilling Mud considering a steel drilling pipe hanging in an oil well, Length of Pipe Hanging in Well is essential in calculating all other values required in drilling & Lower Section of Drill String Length that is in Compression depends on the density of the drilling mud, length of pipe in well and mass density of steel.

How to calculate Mass Density of Steel for Lower Section of Drill String Length in Compression?

The Mass Density of Steel for Lower Section of Drill String Length in Compression is the mass of the fluid per unit volume. The weight density w, of a fluid is the weight of the fluid per unit volume is calculated using Mass Density of Steel = (Density of Drilling Mud*Length of Pipe Hanging in Well)/Lower Section of Drill String Length. To calculate Mass Density of Steel for Lower Section of Drill String Length in Compression, you need Density of Drilling Mud (ρ_m), Length of Pipe Hanging in Well (L) & Lower Section of Drill String Length (L_c). With our tool, you need to enter the respective value for Density of Drilling Mud, Length of Pipe Hanging in Well & Lower Section of Drill String Length and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Mass Density of Steel?

In this formula, Mass Density of Steel uses Density of Drilling Mud, Length of Pipe Hanging in Well & Lower Section of Drill String Length. We can use 2 other way(s) to calculate the same, which is/are as follows -

Mass Density of Steel = Tension on Vertical Drill String/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))
Mass Density of Steel = (Effective Tension/([g]*Cross Section Area of Steel in Pipe*(Length of Pipe Hanging in Well-Coordinate measured Downward from Top))+Density of Drilling Mud)

Home

FREE PDFs

🔍 Search