Rithik Agrawal
National Institute of Technology Karnataka (NITK), Surathkal
Rithik Agrawal has created this Calculator and 300+ more calculators!
Himanshi Sharma
Bhilai Institute of Technology (BIT), Raipur
Himanshi Sharma has verified this Calculator and 500+ more calculators!

11 Other formulas that calculate the same Output

Steel yield strength for Compact Section for LFD when Maximum Unbraced Length is Given
yield strength of steel=((3600-2200*(Smaller Moment/Maximum Moment))*Least Radius of Gyration)/Maximum Unbraced Length GO
Steel yield strength for Braced Non-Compact Section for LFD when Maximum Unbraced Length is Given
yield strength of steel=(20000*Area of Flange)/(Maximum Unbraced Length*Depth of Section) GO
Steel yield strength for Braced Non-Compact Section for LFD when Minimum Flange Thickness is Given
yield strength of steel=(69.6*Minimum Flange Thickness/Width of Projection of Flange)^2 GO
Steel yield strength for Compact Section for LFD when Minimum Flange Thickness is Given
yield strength of steel=(65*Minimum Flange Thickness/Width of Projection of Flange)^2 GO
Steel Yield Strength for milled surface when allowable Bearing Stress for d < 635 mm is Given
yield strength of steel=(20*Allowable Bearing Stresses on Pins/0.6*Diameter )+13 GO
Steel yield strength for Compact Section for LFD when Maximum Bending Moment is Given
yield strength of steel=Maximum Bending Moment/Plastic Section Modulus GO
Steel yield strength for Compact Section for LFD when Minimum Web Thickness is Given
yield strength of steel=(608*Minimum Web Thickness/Depth of Section)^2 GO
Steel yield strength on Pins not subject to rotation for Bridges for LFD when Pin Stresses is Given
yield strength of steel=Allowable Bearing Stresses on Pins/0.8 GO
Steel yield strength for Braced Non-Compact Section for LFD when Maximum Bending Moment is Given
yield strength of steel=Maximum Bending Moment/Section Modulus GO
Steel yield strength on Pins subject to rotation for Bridges for LFD when Pin Stresses is Given
yield strength of steel=Allowable Bearing Stresses on Pins/0.4 GO
Steel yield strength on Pins for Buildings for LFD when Allowable Bearing Stresses is Given
yield strength of steel=Allowable Bearing Stresses on Pins/0.9 GO

Steel Yield Strength when Allowable Unit Stress in Bending is Given Formula

yield strength of steel=Allowable Unit Tensile Stress/0.55
f<sub>y</sub>=F<sub>b</sub>/0.55
More formulas
Shear Capacity for Flexural Members GO
Shear Capacity for Girders with Transverse Stiffeners GO
Allowable Stress when Slenderness Ratio is Less than Cc GO
Allowable Stress when Slenderness Ratio is Equal to or Greater than Cc GO
Maximum Strength for Compression Members GO
Column Gross Effective Area when Maximum Strength is Given GO
Buckling Stress when Maximum Strength is Given GO
Q Factor GO
Steel Yield Strength when Q Factor is Given GO
Buckling Stress when Q Factor is Greater Than 1 GO
Buckling Stress when Q Factor is Less Than or Equal to 1 GO
Steel Yield Strength when Buckling Stress for Q Factor Less Than or Equal to 1 is Given GO
Steel Yield Strength when Buckling Stress for Q Factor Greater Than 1 is Given GO
Allowable Unit Load for Bridges using Structural Carbon Steel GO
Ultimate Unit Load for Bridges using Structural Carbon Steel GO
Allowable Unit Stress in Bending GO
Moment Gradient Factor when Smaller and Larger Beam End Moment is Given GO
Minimum Moment of Inertia of a Transverse Stiffener GO
Actual Stiffener Spacing when Minimum Moment of Inertia of a Transverse Stiffener is Given GO
Web Thickness when Minimum Moment of Inertia of a Transverse Stiffener is Given GO
Gross Cross-Sectional Area of Intermediate Stiffeners GO
Multiplier for allowable stress when flange bending stress does not exceed the allowable stress GO
Maximum bending strength for Symmetrical Flexural Compact Section for LFD of Bridges GO
Maximum bending strength for Symmetrical Flexural Braced Non-Compacted Section for LFD of Bridges GO
Minimum Flange Thickness for Symmetrical Flexural Compact Section for LFD of Bridges GO
Minimum Flange Thickness for Symmetrical Flexural Braced Non-Compact Section for LFD of Bridges GO
Minimum Web Thickness for Symmetrical Flexural Braced Non-Compact Section for LFD of Bridges GO
Minimum Web Thickness for Symmetrical Flexural Compact Section for LFD of Bridges GO
Maximum Unbraced Length for Symmetrical Flexural Compact Section for LFD of Bridges GO
Maximum Unbraced Length for Symmetrical Flexural Braced Non-Compact Section for LFD of Bridges GO
Ultimate Moment Capacity for Symmetrical Flexural Sections for LFD of Bridges GO
Steel yield strength for Compact Section for LFD when Maximum Bending Moment is Given GO
Steel yield strength for Braced Non-Compact Section for LFD when Maximum Bending Moment is Given GO
Steel yield strength for Braced Non-Compact Section for LFD when Minimum Flange Thickness is Given GO
Steel yield strength for Compact Section for LFD when Minimum Flange Thickness is Given GO
Steel yield strength for Compact Section for LFD when Minimum Web Thickness is Given GO
Steel yield strength for Compact Section for LFD when Maximum Unbraced Length is Given GO
Steel yield strength for Braced Non-Compact Section for LFD when Maximum Unbraced Length is Given GO
Plastic Section Modulus for Compact Section for LFD when Maximum Bending Moment is Given GO
Section Modulus for Braced Non-Compact Section for LFD when Maximum Bending Moment is Given GO
Width of Projection of Flange for Braced Non-Compact Section when Maximum Bending Moment is Given GO
Width of Projection of Flange for Compact Section for LFD when Minimum Flange Thickness is Given GO
Depth of Section for Compact Section for LFD when Minimum Web Thickness is Given GO
Unsupported length for Braced Non-Compact Section for LFD when Minimum Web Thickness is Given GO
Depth of Section for Braced Non-Compact Section for LFD when Maximum Unbraced Length is Given GO
Area of Flange for Braced Non-Compact Section for LFD when Maximum Unbraced Length is Given GO
Smaller Moment of unbraced length for Compact Section for LFD when Maximum Unbraced Length is Given GO
Ultimate Moment of unbraced length for Compact Section when Maximum Unbraced Length is Given GO
Allowable Bearing Stresses on Pins for Buildings for LFD GO
Allowable Bearing Stresses on Pins subject to rotation for Bridges for LFD GO
Allowable Bearing Stresses on Pins not subject to rotation for Bridges for LFD GO
Steel yield strength on Pins for Buildings for LFD when Allowable Bearing Stresses is Given GO
Steel yield strength on Pins subject to rotation for Bridges for LFD when Pin Stresses is Given GO
Steel yield strength on Pins not subject to rotation for Bridges for LFD when Pin Stresses is Given GO
Allowable Bearing Stress for expansion rollers and rockers where diameter is up to 635 mm GO
Allowable Bearing Stress for expansion rollers and rockers where diameter is from 635 mm to 3175 mm GO
Steel Yield Strength for milled surface when allowable Bearing Stress for d < 635 mm is Given GO
Steel Yield Strength for milled surface when allowable Bearing Stress for d > 635 mm is Given GO
Diameter of Roller or Rocker for milled surface when Allowable Stress is Given for d < 635 mm GO
Diameter of Roller or Rocker for milled surface when Allowable Stress is Given for d > 635 mm GO
Allowable Bearing Stress for high strength bolts GO
Tensile Strength of connected part when Allowable Bearing Stress for bolts is Given GO
Number of Connectors in Bridges GO
Force in Slab when Number of Connectors in Bridges is Given GO
Reduction Factor when Number of Connectors in Bridges is Given GO
Ultimate Shear Connector Strength when Number of Connectors in Bridges is Given GO
Force in Slab when Total Area of Steel Section is Given GO
Total Area of Steel Section when Force in Slab is Given GO
Steel Yield Strength when Total Area of Steel Section is Given GO
Force in Slab when Effective Concrete Area is Given GO
Effective Concrete Area when Force in Slab is Given GO
28-day Compressive Strength of Concrete when Force in Slab is Given GO
Minimum Number of Connectors for Bridges GO
Force in Slab at Maximum Positive Moments when Minimum Number of Connectors for Bridges is Given GO
Force in Slab at Maximum Negative Moments when Minimum Number of Connectors for Bridges is Given GO
Force in Slab at Maximum Negative Moments when Reinforcing Steel Yield Strength is Given GO
Reduction Factor when Minimum Number of Connectors in Bridges is Given GO
Ultimate Shear Connector Strength when Minimum Number of Connectors in Bridges is Given GO
Area of Longitudinal Reinforcing when Force in Slab at Maximum Negative Moments is Given GO
Reinforcing Steel Yield Strength when Force in Slab at Maximum Negative Moments is Given GO
Allowable Shear stress in Bridges GO
Steel Yield Strength when Allowable Shear stress for Flexural Members in Bridges GO
Shear Buckling Coefficient when Allowable Shear stress for Flexural Members in Bridges is Given GO
Natural frequency of each Cable GO
Span of Cable when Natural frequency of each Cable is Given GO
Cable Tension when Natural frequency of each Cable is Given GO
Fundamental Vibration Mode when Natural frequency of Each Cable is Given GO
Runoff Rate of Rainwater from a bridge during a Rainstorm GO
Average Rainfall Intensity when Runoff Rate of Rainwater from a bridge during a Rainstorm is Given GO
Drainage Area when Runoff Rate of Rainwater from a bridge during a Rainstorm is Given GO
Runoff Coefficient when Runoff Rate of Rainwater from a bridge during a Rainstorm is Given GO
Deck Width for handling the Rainwater Runoff to the Drain Scuppers GO
Shoulder Width when Deck Width for handling the Rainwater Runoff to the Drain Scuppers is Given GO
Traffic Lane when Deck Width for handling the Rainwater Runoff to the Drain Scuppers is Given GO

What is Steel Yield Strength ?

Ultimate tensile strength often shortened to tensile strength (TS), ultimate strength is the maximum stress that a material can withstand while being stretched or pulled before breaking. In brittle materials the ultimate tensile strength is close to the yield point, whereas in ductile materials the ultimate tensile strength can be higher.

How to Calculate Steel Yield Strength when Allowable Unit Stress in Bending is Given?

Steel Yield Strength when Allowable Unit Stress in Bending is Given calculator uses yield strength of steel=Allowable Unit Tensile Stress/0.55 to calculate the yield strength of steel, The Steel Yield Strength when Allowable Unit Stress in Bending is Given formula is defined as maximum stress steel can bare after which it fails. yield strength of steel and is denoted by fy symbol.

How to calculate Steel Yield Strength when Allowable Unit Stress in Bending is Given using this online calculator? To use this online calculator for Steel Yield Strength when Allowable Unit Stress in Bending is Given, enter Allowable Unit Tensile Stress (Fb) and hit the calculate button. Here is how the Steel Yield Strength when Allowable Unit Stress in Bending is Given calculation can be explained with given input values -> 0.018182 = 10000/0.55.

FAQ

What is Steel Yield Strength when Allowable Unit Stress in Bending is Given?
The Steel Yield Strength when Allowable Unit Stress in Bending is Given formula is defined as maximum stress steel can bare after which it fails and is represented as fy=Fb/0.55 or yield strength of steel=Allowable Unit Tensile Stress/0.55. Allowable Unit Tensile Stress is the tensile load at which members are designed.
How to calculate Steel Yield Strength when Allowable Unit Stress in Bending is Given?
The Steel Yield Strength when Allowable Unit Stress in Bending is Given formula is defined as maximum stress steel can bare after which it fails is calculated using yield strength of steel=Allowable Unit Tensile Stress/0.55. To calculate Steel Yield Strength when Allowable Unit Stress in Bending is Given, you need Allowable Unit Tensile Stress (Fb). With our tool, you need to enter the respective value for Allowable Unit Tensile Stress and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
How many ways are there to calculate yield strength of steel?
In this formula, yield strength of steel uses Allowable Unit Tensile Stress. We can use 11 other way(s) to calculate the same, which is/are as follows -
  • yield strength of steel=Maximum Bending Moment/Plastic Section Modulus
  • yield strength of steel=Maximum Bending Moment/Section Modulus
  • yield strength of steel=(69.6*Minimum Flange Thickness/Width of Projection of Flange)^2
  • yield strength of steel=(65*Minimum Flange Thickness/Width of Projection of Flange)^2
  • yield strength of steel=(608*Minimum Web Thickness/Depth of Section)^2
  • yield strength of steel=((3600-2200*(Smaller Moment/Maximum Moment))*Least Radius of Gyration)/Maximum Unbraced Length
  • yield strength of steel=(20000*Area of Flange)/(Maximum Unbraced Length*Depth of Section)
  • yield strength of steel=Allowable Bearing Stresses on Pins/0.9
  • yield strength of steel=Allowable Bearing Stresses on Pins/0.4
  • yield strength of steel=Allowable Bearing Stresses on Pins/0.8
  • yield strength of steel=(20*Allowable Bearing Stresses on Pins/0.6*Diameter )+13
Share Image
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!