Tensile Strength of Single Fillet Lap Joint Calculator

✖Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.ⓘ Tensile Stress [σ_t]			+10% -10%
✖The Length of Weld is the linear distance of each weld segment.ⓘ Length of Weld [l]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖Tensile strength is the stress at the maximum on the engineering stress-strain curve.ⓘ Tensile Strength of Single Fillet Lap Joint [TS]

⎘ Copy

👎

Formula

✖

Tensile Strength of Single Fillet Lap Joint

Formula

`"TS" = 0.707*"σ"_{"t"}*"l"*"t"_{"plate"}`

Example

`"0.002172MPa"=0.707*"32MPa"*"8mm"*"12mm"`

Calculator

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Tensile Strength of Single Fillet Lap Joint Solution

STEP 0: Pre-Calculation Summary

Formula Used

Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate
TS = 0.707*σ_t*l*t_plate
This formula uses 4 Variables

Variables Used

Tensile Strength - (Measured in Pascal) - Tensile strength is the stress at the maximum on the engineering stress-strain curve.
Tensile Stress - (Measured in Pascal) - Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.
Length of Weld - (Measured in Meter) - The Length of Weld is the linear distance of each weld segment.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Tensile Stress: 32 Megapascal --> 32000000 Pascal (Check conversion here)
Length of Weld: 8 Millimeter --> 0.008 Meter (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

TS = 0.707*σ_t*l*t_plate --> 0.707*32000000*0.008*0.012

Evaluating ... ...

TS = 2171.904

STEP 3: Convert Result to Output's Unit

2171.904 Pascal -->0.002171904 Megapascal (Check conversion here)

FINAL ANSWER

0.002171904 ≈ 0.002172 Megapascal <-- Tensile Strength

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Welded Joints » Types of Welded Joints » Tensile Strength of Single Fillet Lap Joint

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< 18 Types of Welded Joints Calculators

Allowable Tensile Stress given Tensile Strength for Single Fillet Lap Joint

Go Tensile Stress = Tensile Strength/(0.707*Length of Weld*Thickness of Plate)

Allowable Tensile Stress given Tensile Strength of Double Fillet Lap

Go Tensile Stress = Tensile Strength/(1.414*Length of Weld*Thickness of Plate)

Tensile Stress given Tensile Force and Length of Weld

Go Tensile Stress = Tensile Force in Butt Weld/(Length of Weld*Depth of Weld)

Depth of Weld given Tensile Force for Butt Weld Joint

Go Depth of Weld = Tensile Force in Butt Weld/(Tensile Stress*Length of Weld)

Tensile Strength of Single Fillet Lap Joint

Go Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate

Tensile Strength of Double Fillet Lap

Go Tensile Strength = 1.414*Tensile Stress*Length of Weld*Thickness of Plate

Tensile Force for Butt Weld Joint given Length of Weld

Go Tensile Force in Butt Weld = Tensile Stress*Length of Weld*Depth of Weld

Tensile Stress given Tensile Strength of Double Fillet Lap and Area of Double Fillet Weld

Go Tensile Stress = Tensile Strength/(Area of Double Fillet Weld)

Tensile Stress given Tensile Strength of Single Fillet Lap and Area of Single Fillet Weld

Go Tensile Stress = Tensile Strength/(Area of Single Fillet Weld)

Tensile Strength of Double Fillet Lap given Area of Double Fillet Weld

Go Tensile Strength = Tensile Stress*Area of Double Fillet Weld

Tensile Strength of Single Fillet Lap given Area of Single Fillet Weld

Go Tensile Strength = Tensile Stress*Area of Single Fillet Weld

Tensile Stress given Tensile Force for Butt Weld Joint

Go Tensile Stress = Tensile Force in Butt Weld/Weld Bed Area

Area of Weld given Tensile Force for Butt Weld Joint

Go Weld Bed Area = Tensile Force in Butt Weld/Tensile Stress

Tensile Force for Butt Weld Joint

Go Tensile Force in Butt Weld = Tensile Stress*Weld Bed Area

Throat Thickness given Area of Fillet Weld for Double Fillet Lap Joint

Go Throat Thickness = Weld Bed Area/(2*Length of Weld)

Throat Thickness given Area of Parallel Fillet Weld

Go Throat Thickness = Weld Bed Area/(2*Length of Weld)

Throat Thickness given Area of Fillet Weld for Single Fillet Lap Joint

Go Throat Thickness = Weld Bed Area/Length of Weld

Throat Thickness for Fillet Weld

Go Throat Thickness = 0.707*Thickness of Plate

Tensile Strength of Single Fillet Lap Joint Formula

Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate
TS = 0.707*σ_t*l*t_plate

What is tensile strength with example?

Tensile strength is a measurement of the force required to pull something such as rope, wire, or a structural beam to the point where it breaks. The tensile strength of a material is the maximum amount of tensile stress that it can take before failure, for example, breaking.

How to Calculate Tensile Strength of Single Fillet Lap Joint?

Tensile Strength of Single Fillet Lap Joint calculator uses Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate to calculate the Tensile Strength, The Tensile strength of single fillet lap joint formula is defined as maximum load that a material can support without fracture when being stretched, divided by the original cross-sectional area of the material. Tensile Strength is denoted by TS symbol.

How to calculate Tensile Strength of Single Fillet Lap Joint using this online calculator? To use this online calculator for Tensile Strength of Single Fillet Lap Joint, enter Tensile Stress (σ_t), Length of Weld (l) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Tensile Strength of Single Fillet Lap Joint calculation can be explained with given input values -> 2.2E-9 = 0.707*32000000*0.008*0.012.

FAQ

What is Tensile Strength of Single Fillet Lap Joint?

The Tensile strength of single fillet lap joint formula is defined as maximum load that a material can support without fracture when being stretched, divided by the original cross-sectional area of the material and is represented as TS = 0.707*σ_t*l*t_plate or Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate. Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force, The Length of Weld is the linear distance of each weld segment & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Tensile Strength of Single Fillet Lap Joint?

The Tensile strength of single fillet lap joint formula is defined as maximum load that a material can support without fracture when being stretched, divided by the original cross-sectional area of the material is calculated using Tensile Strength = 0.707*Tensile Stress*Length of Weld*Thickness of Plate. To calculate Tensile Strength of Single Fillet Lap Joint, you need Tensile Stress (σ_t), Length of Weld (l) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Tensile Stress, Length of Weld & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Tensile Strength?

In this formula, Tensile Strength uses Tensile Stress, Length of Weld & Thickness of Plate. We can use 3 other way(s) to calculate the same, which is/are as follows -

Tensile Strength = 1.414*Tensile Stress*Length of Weld*Thickness of Plate
Tensile Strength = Tensile Stress*Area of Double Fillet Weld
Tensile Strength = Tensile Stress*Area of Single Fillet Weld

Home

FREE PDFs

🔍 Search