Z12 Parameter given Voltage 1 (Z Parameter) Calculator

✖Voltage port 1 is the pressure from an electrical circuit's power source that pushes charged electrons (current) through a conducting loop, enabling them to do work such as illuminating a light.ⓘ Voltage Port 1 [V₁]			+10% -10%
✖Z11 Parameter is driving point impedance at port 1.ⓘ Z11 Parameter [Z₁₁]			+10% -10%
✖Current in port 1 is the magnitude of current flowing through port 1.ⓘ Current in Port 1 [I₁]			+10% -10%
✖Current in port 2 is the magnitude of current flowing through port 2.ⓘ Current in Port 2 [I₂]			+10% -10%

✖Z12 Parameter is reverse transfer impedance.ⓘ Z12 Parameter given Voltage 1 (Z Parameter) [Z₁₂]

⎘ Copy

👎

Formula

✖

Z12 Parameter given Voltage 1 (Z Parameter)

Formula

`"Z"_{"12"} = ("V"_{"1"}-("Z"_{"11"}*"I"_{"1"}))/"I"_{"2"}`

Example

`"422.7451Ω"=("440V"-("11Ω"*"0.8A"))/"1.02A"`

Calculator

LaTeX

Reset

👍

Download Two-Port Network Formula PDF

Z12 Parameter given Voltage 1 (Z Parameter) Solution

STEP 0: Pre-Calculation Summary

Formula Used

Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2
Z₁₂ = (V₁-(Z₁₁*I₁))/I₂
This formula uses 5 Variables

Variables Used

Z12 Parameter - (Measured in Ohm) - Z12 Parameter is reverse transfer impedance.
Voltage Port 1 - (Measured in Volt) - Voltage port 1 is the pressure from an electrical circuit's power source that pushes charged electrons (current) through a conducting loop, enabling them to do work such as illuminating a light.
Z11 Parameter - (Measured in Ohm) - Z11 Parameter is driving point impedance at port 1.
Current in Port 1 - (Measured in Ampere) - Current in port 1 is the magnitude of current flowing through port 1.
Current in Port 2 - (Measured in Ampere) - Current in port 2 is the magnitude of current flowing through port 2.

STEP 1: Convert Input(s) to Base Unit

Voltage Port 1: 440 Volt --> 440 Volt No Conversion Required
Z11 Parameter: 11 Ohm --> 11 Ohm No Conversion Required
Current in Port 1: 0.8 Ampere --> 0.8 Ampere No Conversion Required
Current in Port 2: 1.02 Ampere --> 1.02 Ampere No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

Z₁₂ = (V₁-(Z₁₁*I₁))/I₂ --> (440-(11*0.8))/1.02

Evaluating ... ...

Z₁₂ = 422.745098039216

STEP 3: Convert Result to Output's Unit

422.745098039216 Ohm --> No Conversion Required

FINAL ANSWER

422.745098039216 ≈ 422.7451 Ohm <-- Z12 Parameter

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electrical » Electrical Circuit » Two-Port Network » Z-Parameters » Z12 Parameter given Voltage 1 (Z Parameter)

Credits

Created by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has created this Calculator and 1500+ more calculators!

Verified by Kethavath Srinath

Osmania University (OU), Hyderabad

Kethavath Srinath has verified this Calculator and 1200+ more calculators!

< 23 Z-Parameters Calculators

Z11 Parameter given Voltage 1 (Z Parameter)

Go Z11 Parameter = (Voltage Port 1-(Z12 Parameter*Current in Port 2))/Current in Port 1

Z12 Parameter given Voltage 1 (Z Parameter)

Go Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2

Z21 Parameter given Voltage 2 (Z Parameter)

Go Z21 Parameter = (Voltage Port 2-(Z22 Parameter*Current in Port 2))/Current in Port 1

Z22 Parameter given Voltage 2 (Z Parameter)

Go Z22 Parameter = (Voltage Port 2-(Z21 Parameter*Current in Port 1))/Current in Port 2

Current 2 given Voltage 2 (Z Parameter)

Go Current in Port 2 = (Voltage Port 2-(Z21 Parameter*Current in Port 1))/Z22 Parameter

Current 2 given Voltage 1 (Z Parameter)

Go Current in Port 2 = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Z12 Parameter

Current 1 given Voltage 1 (Z Parameter)

Go Current in Port 1 = (Voltage Port 1-(Z12 Parameter*Current in Port 2))/Z11 Parameter

Voltage 1 (Z Parameter)

Go Voltage Port 1 = (Z11 Parameter*Current in Port 1)+(Z12 Parameter+Current in Port 2)

Voltage 2 (Z Parameter)

Go Voltage Port 2 = (Z21 Parameter*Current in Port 1)+(Z22 Parameter+Current in Port 2)

Current 1 given Z11 Parameter (Z Parameter)

Go Current in Port 1 = Voltage Port 1/Z11 Parameter

Current 1 given Z21 Parameter (Z Parameter)

Go Current in Port 1 = Voltage Port 2/Z21 Parameter

Current 2 given Z22 Parameter (Z Parameter)

Go Current in Port 2 = Voltage Port 2/Z22 Parameter

Driving Point Output Impedance (Z22)

Go Z22 Parameter = Voltage Port 2/Current in Port 2

Driving Point Input Impedance (Z11)

Go Z11 Parameter = Voltage Port 1/Current in Port 1

Output Transfer Impedance (Z21)

Go Z21 Parameter = Voltage Port 2/Current in Port 1

Input Transfer Impedance (Z12)

Go Z12 Parameter = Voltage Port 1/Current in Port 2

Z12 Parameter in Terms of H Parameters

Go Z12 Parameter = H12 Parameter/H22 Parameter

Z21 Parameter in Terms of G Parameters

Go Z21 Parameter = G21 Parameter/G11 Parameter

Z11 Parameter in Terms of T Parameters

Go Z11 Parameter = A Parameter/C Parameter

Z11 Parameter in Terms of Y Parameters

Go Z11 Parameter = Y22 Parameter/Delta-Y

Z11 Parameter in Terms of H Parameters

Go Z11 Parameter = Delta-H/H22 Parameter

Z12 Parameter in Terms of T' Parameters

Go Z12 Parameter = 1/C Inverse Parameter

Z11 Parameter in Terms of G Parameters

Go Z11 Parameter = 1/G11 Parameter

Z12 Parameter given Voltage 1 (Z Parameter) Formula

Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2
Z₁₂ = (V₁-(Z₁₁*I₁))/I₂

What is Z parameter in two port network?

Z parameters (also known as impedance parameters or open-circuit parameters) are properties used in electrical engineering to describe the electrical behavior of linear electrical networks.

How to Calculate Z12 Parameter given Voltage 1 (Z Parameter)?

Z12 Parameter given Voltage 1 (Z Parameter) calculator uses Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2 to calculate the Z12 Parameter, The Z12 Parameter given Voltage 1 (Z Parameter) formula is defined as forward transfer impedance also known as impedance parameters or open-circuit parameters. Z12 Parameter is denoted by Z₁₂ symbol.

How to calculate Z12 Parameter given Voltage 1 (Z Parameter) using this online calculator? To use this online calculator for Z12 Parameter given Voltage 1 (Z Parameter), enter Voltage Port 1 (V₁), Z11 Parameter (Z₁₁), Current in Port 1 (I₁) & Current in Port 2 (I₂) and hit the calculate button. Here is how the Z12 Parameter given Voltage 1 (Z Parameter) calculation can be explained with given input values -> 422.7451 = (440-(11*0.8))/1.02.

FAQ

What is Z12 Parameter given Voltage 1 (Z Parameter)?

The Z12 Parameter given Voltage 1 (Z Parameter) formula is defined as forward transfer impedance also known as impedance parameters or open-circuit parameters and is represented as Z₁₂ = (V₁-(Z₁₁*I₁))/I₂ or Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2. Voltage port 1 is the pressure from an electrical circuit's power source that pushes charged electrons (current) through a conducting loop, enabling them to do work such as illuminating a light, Z11 Parameter is driving point impedance at port 1, Current in port 1 is the magnitude of current flowing through port 1 & Current in port 2 is the magnitude of current flowing through port 2.

How to calculate Z12 Parameter given Voltage 1 (Z Parameter)?

The Z12 Parameter given Voltage 1 (Z Parameter) formula is defined as forward transfer impedance also known as impedance parameters or open-circuit parameters is calculated using Z12 Parameter = (Voltage Port 1-(Z11 Parameter*Current in Port 1))/Current in Port 2. To calculate Z12 Parameter given Voltage 1 (Z Parameter), you need Voltage Port 1 (V₁), Z11 Parameter (Z₁₁), Current in Port 1 (I₁) & Current in Port 2 (I₂). With our tool, you need to enter the respective value for Voltage Port 1, Z11 Parameter, Current in Port 1 & Current in Port 2 and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Z12 Parameter?

In this formula, Z12 Parameter uses Voltage Port 1, Z11 Parameter, Current in Port 1 & Current in Port 2. We can use 3 other way(s) to calculate the same, which is/are as follows -

Z12 Parameter = Voltage Port 1/Current in Port 2
Z12 Parameter = 1/C Inverse Parameter
Z12 Parameter = H12 Parameter/H22 Parameter

Home

FREE PDFs

🔍 Search