Area at Choke Section of Sprue Calculator

✖Area at top section is the surface area at the uppermost part of a component or structure.ⓘ Area at Top Section [At]			+10% -10%
✖Metal head at top section sprue can be defined as the potential head of molten metal at top section of sprue.ⓘ Metal Head at Top Section [h_t]			+10% -10%
✖Head at choke section sprue is the vertical height of molten metal above the narrowest point (choke) in the gating system of a casting, crucial for ensuring proper flow and filling of the mold cavity.ⓘ Head at Choke Section [h_c]			+10% -10%

✖Area at choke section of sprue is the area at that part of sprue where it runs full of metal.ⓘ Area at Choke Section of Sprue [A]

⎘ Copy

👎

Formula

✖

Area at Choke Section of Sprue

Formula

`"A" = "At"*sqrt("h"_{"t"}/"h"_{"c"})`

Example

`"16.7332cm²"="14cm²"*sqrt("10cm"/"7cm")`

Calculator

LaTeX

Reset

👍

Download Casting (Foundry) Formula PDF PDF Image

Area at Choke Section of Sprue Solution

STEP 0: Pre-Calculation Summary

Formula Used

Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section)
A = At*sqrt(h_t/h_c)
This formula uses 1 Functions, 4 Variables

Functions Used

sqrt - A square root function is a function that takes a non-negative number as an input and returns the square root of the given input number., sqrt(Number)

Variables Used

Area at Choke Section - (Measured in Square Meter) - Area at choke section of sprue is the area at that part of sprue where it runs full of metal.
Area at Top Section - (Measured in Square Meter) - Area at top section is the surface area at the uppermost part of a component or structure.
Metal Head at Top Section - (Measured in Meter) - Metal head at top section sprue can be defined as the potential head of molten metal at top section of sprue.
Head at Choke Section - (Measured in Meter) - Head at choke section sprue is the vertical height of molten metal above the narrowest point (choke) in the gating system of a casting, crucial for ensuring proper flow and filling of the mold cavity.

STEP 1: Convert Input(s) to Base Unit

Area at Top Section: 14 Square Centimeter --> 0.0014 Square Meter (Check conversion here)
Metal Head at Top Section: 10 Centimeter --> 0.1 Meter (Check conversion here)
Head at Choke Section: 7 Centimeter --> 0.07 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

A = At*sqrt(h_t/h_c) --> 0.0014*sqrt(0.1/0.07)

Evaluating ... ...

A = 0.00167332005306815

STEP 3: Convert Result to Output's Unit

0.00167332005306815 Square Meter -->16.7332005306815 Square Centimeter (Check conversion here)

FINAL ANSWER

16.7332005306815 ≈ 16.7332 Square Centimeter <-- Area at Choke Section

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Casting (Foundry) » Gating System For Casting » Sprue » Area at Choke Section of Sprue

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< 4 Sprue Calculators

Area at Choke Section of Sprue

Go Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section)

Area at Top Section of Sprue

Go Area at Top Section = Area at Choke Section*sqrt(Head at Choke Section/Metal Head at Top Section)

Metal Head at Choke Section of Sprue

Go Head at Choke Section = Metal Head at Top Section*(Area at Top Section/Area at Choke Section)^2

Metal Head at Top Section of Sprue

Go Metal Head at Top Section = Head at Choke Section*(Area at Choke Section/Area at Top Section)^2

Area at Choke Section of Sprue Formula

Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section)
A = At*sqrt(h_t/h_c)

What is sprue?

Sprue is the channel through which the molten metal is brought into the parting plane, where it enters the runners and gates to ultimately reach the mould cavity. The molten metal when moving from top of the cope to the parting plane gains in velocity, and as a consequence, requires a smaller area of cross section for the same amount of metal to flow at the top. If the sprue were to be straight-cylindrical then the metal flow would not be full at the bottom, but some low-pressure area would be created around the metal in the sprue.

How to Calculate Area at Choke Section of Sprue?

Area at Choke Section of Sprue calculator uses Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section) to calculate the Area at Choke Section, The Area at choke section of sprue is the area at that part of sprue where it runs full of metal. It can be taken conveniently anywhere on the sprue. Area at Choke Section is denoted by A symbol.

How to calculate Area at Choke Section of Sprue using this online calculator? To use this online calculator for Area at Choke Section of Sprue, enter Area at Top Section (At), Metal Head at Top Section (h_t) & Head at Choke Section (h_c) and hit the calculate button. Here is how the Area at Choke Section of Sprue calculation can be explained with given input values -> 167332 = 0.0014*sqrt(0.1/0.07).

FAQ

What is Area at Choke Section of Sprue?

The Area at choke section of sprue is the area at that part of sprue where it runs full of metal. It can be taken conveniently anywhere on the sprue and is represented as A = At*sqrt(h_t/h_c) or Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section). Area at top section is the surface area at the uppermost part of a component or structure, Metal head at top section sprue can be defined as the potential head of molten metal at top section of sprue & Head at choke section sprue is the vertical height of molten metal above the narrowest point (choke) in the gating system of a casting, crucial for ensuring proper flow and filling of the mold cavity.

How to calculate Area at Choke Section of Sprue?

The Area at choke section of sprue is the area at that part of sprue where it runs full of metal. It can be taken conveniently anywhere on the sprue is calculated using Area at Choke Section = Area at Top Section*sqrt(Metal Head at Top Section/Head at Choke Section). To calculate Area at Choke Section of Sprue, you need Area at Top Section (At), Metal Head at Top Section (h_t) & Head at Choke Section (h_c). With our tool, you need to enter the respective value for Area at Top Section, Metal Head at Top Section & Head at Choke Section and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search