Anirudh Singh
National Institute of Technology (NIT), Jamshedpur
Anirudh Singh has created this Calculator and 100+ more calculators!

11 Other formulas that you can solve using the same Inputs

Heat Loss due to Pipe
Heat Loss due to Pipe=(Force*Length*Fluid Velocity^2)/(2*Diameter *Acceleration Due To Gravity) GO
EMF Of Dc Machine When Constant Of The DC Machine Is Given
Electromotive Force=Constant Of The DC Machine*Angular Speed*Flux per pole GO
Reynolds Number for Circular Tubes
Reynolds Number=Density*Fluid Velocity*Diameter /Dynamic viscosity GO
Perimeter of a Semicircle when circumference of circle is given
Perimeter=(Circumference of Circle/2)+Diameter GO
Diameter of circumscribing sphere when diameter and height of circumscribed cylinder is known
Diameter of Sphere=sqrt(Diameter ^2+Height^2) GO
Area of a Circle when diameter is given
Area of Circle=(pi/4)*Diameter ^2 GO
Perimeter of a quarter circle when diameter is given
Perimeter=Diameter *((pi/4)+1) GO
Perimeter of a Semicircle when diameter is given
Perimeter=Diameter *((pi/2)+1) GO
Area of a quarter circle when diameter is given
Area=(pi*(Diameter )^2)/16 GO
Area of a Semicircle when diameter is given
Area=(pi*(Diameter )^2)/8 GO
Radius of a circle when diameter is given
Radius=Diameter /2 GO

Cutting Speed Formula

Cutting Speed=pi*Diameter *Angular Speed
More formulas
Gibbs Free Energy GO
Coefficient of Friction GO
Atomic Packing Factor GO
Atomic Packing Factor Percentage GO
Void Percentage GO
Solidification Time GO
Caine's Formula GO
Shape Factor GO
Modulus Method GO
Draw Ratio GO
Vertical Gating GO
Aspiration Effect GO
Flow Stress GO
Bite Angle GO
Bend Allowance GO
Extrusion and Wire drawing GO
Shear Angle GO
Shear Strain GO
Shear Strain GO
Sheer Yield Strength GO
Specific Power Consumption GO
Peak to Valley Height GO
Mass Removal Rate GO
Dilution GO
Resistance Welding GO
Diameter of a Nugget GO
Tolerance GO
Relation in voltage and arc length GO
Electro Discharge Machining GO
Volumetric Removal Rate in electrochemical machining GO
Coefficient of Friction (using forces) GO
Shear Force GO
Normal Force GO
Peak to Valley Height GO
Bottom Gating GO
Maximum Profit Rate GO
Maximum Production Rate GO
Total Minimum Cost GO
Height of Nugget GO
Punch Load GO
Roll Separating Force GO

What is importance of Cutting speed?

Cutting speed and feed determines the surface finish, power requirements, and material removal rate.

How to Calculate Cutting Speed?

Cutting Speed calculator uses Cutting Speed=pi*Diameter *Angular Speed to calculate the Cutting Speed, Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute). Cutting Speed and is denoted by Vcutting symbol.

How to calculate Cutting Speed using this online calculator? To use this online calculator for Cutting Speed, enter Diameter (d) and Angular Speed (ω) and hit the calculate button. Here is how the Cutting Speed calculation can be explained with given input values -> 1.113E+7 = pi*10*1799.99999999987.

FAQ

What is Cutting Speed?
Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute) and is represented as Vcutting=pi*d*ω or Cutting Speed=pi*Diameter *Angular Speed. Diameter is a straight line passing from side to side through the center of a body or figure, especially a circle or sphere and Angular speed is defined as the rate of change of angular displacement.
How to calculate Cutting Speed?
Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute) is calculated using Cutting Speed=pi*Diameter *Angular Speed. To calculate Cutting Speed, you need Diameter (d) and Angular Speed (ω). With our tool, you need to enter the respective value for Diameter and Angular Speed and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Share Image
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!