Radius of Influence given Coefficient of Transmissibility with Base 10 Calculator

✖Radius of well is defined as the distance from center of well to its outer boundary.ⓘ Radius of well [r]			+10% -10%
✖Coefficient of transmissibility is defined as the rate of flow of water in gallons per day through a vertical strip of the aquifer.ⓘ Coefficient of Transmissibility [T_envi]			+10% -10%
✖Initial Aquifer Thickness is the aquifer thickness at initial stage before pumping.ⓘ Initial Aquifer Thickness [H_i]			+10% -10%
✖Depth of Water in the well measured above the impermeable layer.ⓘ Depth of Water [h_w]			+10% -10%
✖Discharge of Liquid is the rate of flow of a liquid.ⓘ Discharge of Liquid [Q_li]			+10% -10%

✖Radius of Influence measured from the center of the well to the point where drawdown curve meets the original water table.ⓘ Radius of Influence given Coefficient of Transmissibility with Base 10 [R_w]

⎘ Copy

👎

Formula

✖

Radius of Influence given Coefficient of Transmissibility with Base 10

Formula

`"R"_{"w"} = "r"*10^((2.72*"T"_{"envi"}*("H"_{"i"}-"h"_{"w"}))/"Q"_{"li"})`

Example

`"7.984749m"="7.5m"*10^((2.72*"1.5m²/s"*("2.54m"-"2.44m"))/"15m³/s")`

Calculator

LaTeX

Reset

👍

Download Environmental Engineering Formula PDF

Radius of Influence given Coefficient of Transmissibility with Base 10 Solution

STEP 0: Pre-Calculation Summary

Formula Used

Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid)
R_w = r*10^((2.72*T_envi*(H_i-h_w))/Q_li)
This formula uses 6 Variables

Variables Used

Radius of Influence - (Measured in Meter) - Radius of Influence measured from the center of the well to the point where drawdown curve meets the original water table.
Radius of well - (Measured in Meter) - Radius of well is defined as the distance from center of well to its outer boundary.
Coefficient of Transmissibility - (Measured in Square Meter per Second) - Coefficient of transmissibility is defined as the rate of flow of water in gallons per day through a vertical strip of the aquifer.
Initial Aquifer Thickness - (Measured in Meter) - Initial Aquifer Thickness is the aquifer thickness at initial stage before pumping.
Depth of Water - (Measured in Meter) - Depth of Water in the well measured above the impermeable layer.
Discharge of Liquid - (Measured in Cubic Meter per Second) - Discharge of Liquid is the rate of flow of a liquid.

STEP 1: Convert Input(s) to Base Unit

Radius of well: 7.5 Meter --> 7.5 Meter No Conversion Required
Coefficient of Transmissibility: 1.5 Square Meter per Second --> 1.5 Square Meter per Second No Conversion Required
Initial Aquifer Thickness: 2.54 Meter --> 2.54 Meter No Conversion Required
Depth of Water: 2.44 Meter --> 2.44 Meter No Conversion Required
Discharge of Liquid: 15 Cubic Meter per Second --> 15 Cubic Meter per Second No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R_w = r*10^((2.72*T_envi*(H_i-h_w))/Q_li) --> 7.5*10^((2.72*1.5*(2.54-2.44))/15)

Evaluating ... ...

R_w = 7.98474890288484

STEP 3: Convert Result to Output's Unit

7.98474890288484 Meter --> No Conversion Required

FINAL ANSWER

7.98474890288484 ≈ 7.984749 Meter <-- Radius of Influence

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Civil » Environmental Engineering » Water Resources : Ground Water » Well Hydraulics » Confined Aquifer » Radius of Influence » Radius of Influence given Coefficient of Transmissibility with Base 10

Credits

Created by Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 2200+ more calculators!

Verified by Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 2600+ more calculators!

< 8 Radius of Influence Calculators

Radius of Influence given Discharge in Confined Aquifer

Go Radius of Influence = Radius of well*exp((2*pi*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)

Radius of Influence given Confined Aquifer Discharge

Go Radius of Influence = Radius of well*exp((2*pi*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*Total Drawdown in Well)/Discharge of Liquid)

Radius of Influence given Discharge in Confined Aquifer with Base 10

Go Radius of Influence = Radius of well*10^((2.72*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)

Radius of Influence given Coefficient of Transmissibility

Go Radius of Influence = Radius of well*exp((2*pi*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)

Radius of Influence given Confined Aquifer Discharge with Base 10

Go Radius of Influence = Radius of well*10^((2.72*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*Total Drawdown in Well)/Discharge of Liquid)

Radius of Influence given Drawdown at Well

Go Radius of Influence = Radius of well*exp((2*pi*Coefficient of Transmissibility*Total Drawdown in Well)/Discharge of Liquid)

Radius of Influence given Coefficient of Transmissibility with Base 10

Go Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid)

Radius of Influence given Drawdown at Well with Base 10

Go Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*Total Drawdown in Well)/Discharge of Liquid)

Radius of Influence given Coefficient of Transmissibility with Base 10 Formula

Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid)
R_w = r*10^((2.72*T_envi*(H_i-h_w))/Q_li)

What is Confined Aquifer?

A confined aquifer is an aquifer below the land surface that is saturated with water. Layers of impermeable material are both above and below the aquifer, causing it to be under pressure so that when the aquifer is penetrated by a well, the water will rise above the top of the aquifer.

How to Calculate Radius of Influence given Coefficient of Transmissibility with Base 10?

Radius of Influence given Coefficient of Transmissibility with Base 10 calculator uses Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid) to calculate the Radius of Influence, The Radius of Influence given Coefficient of Transmissibility with Base 10 is defined as the value of radius of influence when we have prior information of other parameters used. Radius of Influence is denoted by R_w symbol.

How to calculate Radius of Influence given Coefficient of Transmissibility with Base 10 using this online calculator? To use this online calculator for Radius of Influence given Coefficient of Transmissibility with Base 10, enter Radius of well (r), Coefficient of Transmissibility (T_envi), Initial Aquifer Thickness (H_i), Depth of Water (h_w) & Discharge of Liquid (Q_li) and hit the calculate button. Here is how the Radius of Influence given Coefficient of Transmissibility with Base 10 calculation can be explained with given input values -> 7.984749 = 7.5*10^((2.72*1.5*(2.54-2.44))/15).

FAQ

What is Radius of Influence given Coefficient of Transmissibility with Base 10?

The Radius of Influence given Coefficient of Transmissibility with Base 10 is defined as the value of radius of influence when we have prior information of other parameters used and is represented as R_w = r*10^((2.72*T_envi*(H_i-h_w))/Q_li) or Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid). Radius of well is defined as the distance from center of well to its outer boundary, Coefficient of transmissibility is defined as the rate of flow of water in gallons per day through a vertical strip of the aquifer, Initial Aquifer Thickness is the aquifer thickness at initial stage before pumping, Depth of Water in the well measured above the impermeable layer & Discharge of Liquid is the rate of flow of a liquid.

How to calculate Radius of Influence given Coefficient of Transmissibility with Base 10?

The Radius of Influence given Coefficient of Transmissibility with Base 10 is defined as the value of radius of influence when we have prior information of other parameters used is calculated using Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge of Liquid). To calculate Radius of Influence given Coefficient of Transmissibility with Base 10, you need Radius of well (r), Coefficient of Transmissibility (T_envi), Initial Aquifer Thickness (H_i), Depth of Water (h_w) & Discharge of Liquid (Q_li). With our tool, you need to enter the respective value for Radius of well, Coefficient of Transmissibility, Initial Aquifer Thickness, Depth of Water & Discharge of Liquid and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Radius of Influence?

In this formula, Radius of Influence uses Radius of well, Coefficient of Transmissibility, Initial Aquifer Thickness, Depth of Water & Discharge of Liquid. We can use 7 other way(s) to calculate the same, which is/are as follows -

Radius of Influence = Radius of well*exp((2*pi*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)
Radius of Influence = Radius of well*10^((2.72*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)
Radius of Influence = Radius of well*exp((2*pi*Coefficient of Transmissibility*(Initial Aquifer Thickness-Depth of Water))/Discharge at Time t=0)
Radius of Influence = Radius of well*exp((2*pi*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*Total Drawdown in Well)/Discharge of Liquid)
Radius of Influence = Radius of well*10^((2.72*Coefficient of Permeability in Well Hydraulics*Aquifer Thickness During Pumping*Total Drawdown in Well)/Discharge of Liquid)
Radius of Influence = Radius of well*exp((2*pi*Coefficient of Transmissibility*Total Drawdown in Well)/Discharge of Liquid)
Radius of Influence = Radius of well*10^((2.72*Coefficient of Transmissibility*Total Drawdown in Well)/Discharge of Liquid)

Home

FREE PDFs

🔍 Search