Series Resistance in N-type Calculator

Engineering Chemistry Financial Health More >>

↳

Electronics Chemical Engineering Civil Electrical More >>

⤿

Solid State Devices Amplifiers Analog Communications Analog Electronics More >>

⤿

SSD Junction Electrons and Holes Energy Band and Charge Carrier Semiconductor Carriers

✖Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.ⓘ Source Voltage [V]			+10% -10%
✖Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.ⓘ Junction Voltage [V_j]			+10% -10%
✖Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.ⓘ Electric Current [I]			+10% -10%
✖Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.ⓘ Series Resistance in P Junction [R_se(p)]			+10% -10%

✖Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.ⓘ Series Resistance in N-type [R_se(n)]

⎘ Copy

👎

Formula

LaTeX

Reset

👍

Download SSD Junction Formulas PDF

Series Resistance in N-type Solution

STEP 0: Pre-Calculation Summary

Formula Used

Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction
R_se(n) = ((V-V_j)/I)-R_se(p)
This formula uses 5 Variables

Variables Used

Series Resistance in N Junction - (Measured in Ohm) - Series Resistance in n Junction is defined as the total resistance in the series inside a circuit at n-junction.
Source Voltage - (Measured in Volt) - Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points.
Junction Voltage - (Measured in Volt) - Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers.
Electric Current - (Measured in Ampere) - Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device.
Series Resistance in P Junction - (Measured in Ohm) - Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.

STEP 1: Convert Input(s) to Base Unit

Source Voltage: 120 Volt --> 120 Volt No Conversion Required
Junction Voltage: 119.9 Volt --> 119.9 Volt No Conversion Required
Electric Current: 0.2 Milliampere --> 0.0002 Ampere (Check conversion here)
Series Resistance in P Junction: 23.3 Ohm --> 23.3 Ohm No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

R_se(n) = ((V-V_j)/I)-R_se(p) --> ((120-119.9)/0.0002)-23.3

Evaluating ... ...

R_se(n) = 476.699999999972

STEP 3: Convert Result to Output's Unit

476.699999999972 Ohm --> No Conversion Required

FINAL ANSWER

476.699999999972 ≈ 476.7 Ohm <-- Series Resistance in N Junction

(Calculation completed in 00.007 seconds)

You are here -

Home » Engineering » Electronics » Solid State Devices » SSD Junction » Series Resistance in N-type

Credits

Created by Shobhit Dimri

Bipin Tripathi Kumaon Institute of Technology (BTKIT), Dwarahat

Shobhit Dimri has created this Calculator and 900+ more calculators!

Verified by Urvi Rathod

Vishwakarma Government Engineering College (VGEC), Ahmedabad

Urvi Rathod has verified this Calculator and 1900+ more calculators!

< SSD Junction Calculators

Junction Capacitance

LaTeX Go Junction Capacitance = (Junction Area/2)*sqrt((2*[Charge-e]*Constant Length Offset*Doping Concentration of Base)/(Source Voltage-Source Voltage 1))

Series Resistance in P-type

LaTeX Go Series Resistance in P Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in N Junction

Junction Voltage

LaTeX Go Junction Voltage = Source Voltage-(Series Resistance in P Junction+Series Resistance in N Junction)*Electric Current

N-Type Width

LaTeX Go Charge Penetration N-type = Total Acceptor Charge/(Junction Area*Acceptor Concentration*[Charge-e])

Series Resistance in N-type Formula

LaTeX Go

Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction
R_se(n) = ((V-V_j)/I)-R_se(p)

What happens in series resistance?

In a series resistor network the individual resistors add together to give an equivalent resistance, ( RT ) of the series combination. The resistors in a series circuit can be interchanged without affecting the total resistance, current, or power to each resistor or the circuit.

How to Calculate Series Resistance in N-type?

Series Resistance in N-type calculator uses Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction to calculate the Series Resistance in N Junction, The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction. Series Resistance in N Junction is denoted by R_se(n) symbol.

How to calculate Series Resistance in N-type using this online calculator? To use this online calculator for Series Resistance in N-type, enter Source Voltage (V), Junction Voltage (V_j), Electric Current (I) & Series Resistance in P Junction (R_se(p)) and hit the calculate button. Here is how the Series Resistance in N-type calculation can be explained with given input values -> 476.7 = ((120-119.9)/0.0002)-23.3.

FAQ

What is Series Resistance in N-type?

The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction and is represented as R_se(n) = ((V-V_j)/I)-R_se(p) or Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction. Source Voltage is the difference in electric potential between two points, which is defined as the work needed per unit of charge to move a test charge between the two points, Junction voltage is the portion of the channel in a metal oxide field-effect transistor in which there are no charge carriers, Electric Current is the time rate of flow of charge through a cross sectional area in a solid state device & Series Resistance in p Junction is defined as the total resistance in the series inside a circuit at p-junction.

How to calculate Series Resistance in N-type?

The Series Resistance in N-type formula is defined as the total resistance in the series inside a a circuit at n-junction is calculated using Series Resistance in N Junction = ((Source Voltage-Junction Voltage)/Electric Current)-Series Resistance in P Junction. To calculate Series Resistance in N-type, you need Source Voltage (V), Junction Voltage (V_j), Electric Current (I) & Series Resistance in P Junction (R_se(p)). With our tool, you need to enter the respective value for Source Voltage, Junction Voltage, Electric Current & Series Resistance in P Junction and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Spanish French German Russian Italian Portuguese Polish Dutch

Home FREE PDFs

🔍 Search