Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft Solution

STEP 0: Pre-Calculation Summary
Formula Used
Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter)
N = U/(pi*D)
This formula uses 1 Constants, 3 Variables
Constants Used
pi - Archimedes' constant Value Taken As 3.14159265358979323846264338327950288
Variables Used
Shaft Speed - (Measured in Hertz) - The Shaft Speed is the speed of rotation of the Shaft.
Surface Velocity of Shaft - (Measured in Meter per Second) - Surface velocity of shaft is defined as the velocity of a point on the surface of the shaft.
Shaft Diameter - (Measured in Meter) - The Shaft Diameter is defined as the diameter of the hole in the iron laminations that contains the shaft.
STEP 1: Convert Input(s) to Base Unit
Surface Velocity of Shaft: 6.6 Meter per Second --> 6.6 Meter per Second No Conversion Required
Shaft Diameter: 3.6 Meter --> 3.6 Meter No Conversion Required
STEP 2: Evaluate Formula
Substituting Input Values in Formula
N = U/(pi*D) --> 6.6/(pi*3.6)
Evaluating ... ...
N = 0.583568124670283
STEP 3: Convert Result to Output's Unit
0.583568124670283 Hertz -->0.583568124670283 Revolution per Second (Check conversion here)
FINAL ANSWER
0.583568124670283 0.583568 Revolution per Second <-- Shaft Speed
(Calculation completed in 00.004 seconds)

Credits

National Institute of Technology Calicut (NIT Calicut), Calicut, Kerala
Peri Krishna Karthik has created this Calculator and 200+ more calculators!
Verified by Anshika Arya
National Institute Of Technology (NIT), Hamirpur
Anshika Arya has verified this Calculator and 2500+ more calculators!

9 Vertical Shaft Rotating in Guide Bearing Calculators

Radial Clearance given Eccentricity Ratio and Thickness of Film at any Position
Go Radial Clearance = Oil Film Thickness at any Position θ/(1+Eccentricity Ratio*cos(Angle Measured from Point of Minimum of Oil Film))
Eccentricity Ratio given Radial Clearance and Film Thickness at any Position
Go Eccentricity Ratio = (Oil Film Thickness at any Position θ/Radial Clearance-1)/cos(Angle Measured from Point of Minimum of Oil Film)
Oil Film Thickness at any Position in Journal Bearing
Go Oil Film Thickness at any Position θ = Radial Clearance*(1+Eccentricity Ratio*cos(Angle Measured from Point of Minimum of Oil Film))
Journal Diameter given Angular Length of Bearing and Length of Bearing in Direction of Motion
Go Shaft Diameter = (2*Length of Bearing in Direction of Motion)/(Angular or Circumferential Length of Bearing)
Angular Length of Bearing given Length of Bearing in Direction of Motion
Go Angular or Circumferential Length of Bearing = (2*Length of Bearing in Direction of Motion)/(Shaft Diameter)
Length of Bearing in Direction of Motion
Go Length of Bearing in Direction of Motion = (Shaft Diameter*Angular or Circumferential Length of Bearing)/2
Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft
Go Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter)
Diameter of Shaft given Shaft Speed and Surface Velocity of Shaft
Go Shaft Diameter = Surface Velocity of Shaft/(pi*Shaft Speed)
Surface Velocity of Shaft given Shaft Speed and Diameter
Go Surface Velocity of Shaft = pi*Shaft Diameter*Shaft Speed

Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft Formula

Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter)
N = U/(pi*D)

How are bearings classified?

Depending upon the direction of load to be supported, the bearings can be classified as Radial and Thrust bearings. In radial bearings, the load acts perpendicular to the direction of motion of the moving element. In thrust bearings, the load acts along the axis of rotation. Depending upon the nature of contact, the bearings can be classified as sliding contact and rolling contact bearings. In sliding contact bearings, the sliding takes place along the surfaces of contact between the moving element and the fixed element. The sliding contact bearings are also known as plain bearings. In rolling contact bearings, the steel balls or rollers, are interposed between the moving and fixed elements. The balls offer rolling friction at two points for each ball or roller.

How are sliding contact bearings classified?

The sliding contact bearings in which the sliding action is guided in a straight line and carrying radial loads may be called slipper or guide bearings and those in which the sliding action is along the circumference of a circle or an arc of a circle are known as journal or sleeve bearings. When the angle of contact of the bearing with the journal is 360° then the bearing is called a full journal bearing and is used to accommodate bearing loads in any radial direction. When the angle of contact of the bearing with the journal is 120°, then the bearing is said to be partial journal bearing. This type of bearing has less friction than full journal bearing, but it can be used only where the load is always in one direction. The full and partial journal bearings may be called as clearance bearings because the diameter of the journal is less than that of bearing. When a partial journal bearing has no clearance i.e. the diameters of the journal and bearing are equal, then the bearing is called a fitted bearing.

How to Calculate Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft?

Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft calculator uses Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter) to calculate the Shaft Speed, The Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft formula is used to find the angular velocity of the shaft when the diameter and speed of a point on the surface of the shaft are known. Shaft Speed is denoted by N symbol.

How to calculate Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft using this online calculator? To use this online calculator for Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft, enter Surface Velocity of Shaft (U) & Shaft Diameter (D) and hit the calculate button. Here is how the Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft calculation can be explained with given input values -> 0.583568 = 6.6/(pi*3.6).

FAQ

What is Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft?
The Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft formula is used to find the angular velocity of the shaft when the diameter and speed of a point on the surface of the shaft are known and is represented as N = U/(pi*D) or Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter). Surface velocity of shaft is defined as the velocity of a point on the surface of the shaft & The Shaft Diameter is defined as the diameter of the hole in the iron laminations that contains the shaft.
How to calculate Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft?
The Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft formula is used to find the angular velocity of the shaft when the diameter and speed of a point on the surface of the shaft are known is calculated using Shaft Speed = Surface Velocity of Shaft/(pi*Shaft Diameter). To calculate Speed of Shaft given Diameter of Shaft and Surface Velocity of Shaft, you need Surface Velocity of Shaft (U) & Shaft Diameter (D). With our tool, you need to enter the respective value for Surface Velocity of Shaft & Shaft Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.
Let Others Know
Facebook
Twitter
Reddit
LinkedIn
Email
WhatsApp
Copied!