Taper produced due to side sparks Calculator

✖Empirical constant is defined as the constant used to calculate the Taper produced during EDM due to side sparks.ⓘ Empirical Constant [K_T]			+10% -10%
✖The smaller diameter is the smaller of all diameters of a given object.ⓘ Smaller Diameter [d]			+10% -10%

✖Taper produced in EDM is the taper produced due to side sparks during EDM.ⓘ Taper produced due to side sparks [T_sd]

⎘ Copy

👎

Formula

✖

Taper produced due to side sparks

Formula

`"T"_{"sd"} = "K"_{"T"}*"d"^2`

Example

`"0.199872"="0.1388"*("1.2m")^2`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Taper produced due to side sparks Solution

STEP 0: Pre-Calculation Summary

Formula Used

Taper Produced in EDM = Empirical Constant*Smaller Diameter^2
T_sd = K_T*d^2
This formula uses 3 Variables

Variables Used

Taper Produced in EDM - Taper produced in EDM is the taper produced due to side sparks during EDM.
Empirical Constant - Empirical constant is defined as the constant used to calculate the Taper produced during EDM due to side sparks.
Smaller Diameter - (Measured in Meter) - The smaller diameter is the smaller of all diameters of a given object.

STEP 1: Convert Input(s) to Base Unit

Empirical Constant: 0.1388 --> No Conversion Required
Smaller Diameter: 1.2 Meter --> 1.2 Meter No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

T_sd = K_T*d^2 --> 0.1388*1.2^2

Evaluating ... ...

T_sd = 0.199872

STEP 3: Convert Result to Output's Unit

0.199872 --> No Conversion Required

FINAL ANSWER

0.199872 <-- Taper Produced in EDM

(Calculation completed in 00.008 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Taper Formation » Taper produced due to side sparks

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Sai Venkata Phanindra Chary Arendra

Vallurupalli Nageswara Rao Vignana Jyothi Institute of Engineering and Technology (VNRVJIET), Hyderabad

Sai Venkata Phanindra Chary Arendra has verified this Calculator and 300+ more calculators!

< 9 Taper Formation Calculators

Volume of crater made by electric spark

Go Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter))

Empirical constant for taper

Go Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)

Depth of machined surface

Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Empirical Constant*Smaller Diameter^2)

Upper diameter of hole

Go Larger Diameter = 2*Depth of Machined Surface*Empirical Constant*Smaller Diameter^2+Smaller Diameter

Depth of machined surface given taper

Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM)

Smaller diameter of crater given Taper

Go Smaller Diameter = Larger Diameter-2*Depth of Machined Surface*Taper Produced in EDM

Largest size of hole given taper

Go Larger Diameter = 2*Depth of Machined Surface*Taper Produced in EDM+Smaller Diameter

Smallest diameter of hole given empirical constant

Go Smaller Diameter = sqrt(Taper Produced in EDM/Empirical Constant)

Taper produced due to side sparks

Go Taper Produced in EDM = Empirical Constant*Smaller Diameter^2

Taper produced due to side sparks Formula

Taper Produced in EDM = Empirical Constant*Smaller Diameter^2
T_sd = K_T*d^2

What factors affects surface finish during EDM?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time the material removal rate can be maintained by increasing the frequency.

How to Calculate Taper produced due to side sparks?

Taper produced due to side sparks calculator uses Taper Produced in EDM = Empirical Constant*Smaller Diameter^2 to calculate the Taper Produced in EDM, The Taper produced due to side sparks formula is defined as to be proportional to the square of the smaller diameter. Taper Produced in EDM is denoted by T_sd symbol.

How to calculate Taper produced due to side sparks using this online calculator? To use this online calculator for Taper produced due to side sparks, enter Empirical Constant (K_T) & Smaller Diameter (d) and hit the calculate button. Here is how the Taper produced due to side sparks calculation can be explained with given input values -> 1.8 = 0.1388*1.2^2.

FAQ

What is Taper produced due to side sparks?

The Taper produced due to side sparks formula is defined as to be proportional to the square of the smaller diameter and is represented as T_sd = K_T*d^2 or Taper Produced in EDM = Empirical Constant*Smaller Diameter^2. Empirical constant is defined as the constant used to calculate the Taper produced during EDM due to side sparks & The smaller diameter is the smaller of all diameters of a given object.

How to calculate Taper produced due to side sparks?

The Taper produced due to side sparks formula is defined as to be proportional to the square of the smaller diameter is calculated using Taper Produced in EDM = Empirical Constant*Smaller Diameter^2. To calculate Taper produced due to side sparks, you need Empirical Constant (K_T) & Smaller Diameter (d). With our tool, you need to enter the respective value for Empirical Constant & Smaller Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search