Thickness of plates given crushing strength for 'n' number of rivets Calculator

✖Crushing strength is the capacity of a material or structure to withstand loads tending to reduce size.ⓘ Crushing strength [P_c]			+10% -10%
✖Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet.ⓘ Number of Rivets Per Pitch [n]			+10% -10%
✖Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.ⓘ Crushing stress [σ_c]			+10% -10%
✖Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.ⓘ Rivet Diameter [D_rivet]			+10% -10%

✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of plates given crushing strength for 'n' number of rivets [t_plate]

⎘ Copy

👎

Formula

✖

Thickness of plates given crushing strength for 'n' number of rivets

Formula

`"t"_{"plate"} = "P"_{"c"}/("n"*"σ"_{"c"}*"D"_{"rivet"})`

Example

`"74.07407mm"="6.4kN"/("2"*"2.4MPa"*"18mm")`

Calculator

LaTeX

Reset

👍

Download Strength of Materials Formula PDF

Thickness of plates given crushing strength for 'n' number of rivets Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)
t_plate = P_c/(n*σ_c*D_rivet)
This formula uses 5 Variables

Variables Used

Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.
Crushing strength - (Measured in Newton) - Crushing strength is the capacity of a material or structure to withstand loads tending to reduce size.
Number of Rivets Per Pitch - Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet.
Crushing stress - (Measured in Pascal) - Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest.
Rivet Diameter - (Measured in Meter) - Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

STEP 1: Convert Input(s) to Base Unit

Crushing strength: 6.4 Kilonewton --> 6400 Newton (Check conversion here)
Number of Rivets Per Pitch: 2 --> No Conversion Required
Crushing stress: 2.4 Megapascal --> 2400000 Pascal (Check conversion here)
Rivet Diameter: 18 Millimeter --> 0.018 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

t_plate = P_c/(n*σ_c*D_rivet) --> 6400/(2*2400000*0.018)

Evaluating ... ...

t_plate = 0.0740740740740741

STEP 3: Convert Result to Output's Unit

0.0740740740740741 Meter -->74.0740740740741 Millimeter (Check conversion here)

FINAL ANSWER

74.0740740740741 ≈ 74.07407 Millimeter <-- Thickness of Plate

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Riveted Joint » Strength of a Riveted Joint » Thickness of Plate » Thickness of plates given crushing strength for 'n' number of rivets

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< 7 Thickness of Plate Calculators

Thickness of plate given efficiency of riveted joint

Go Thickness of Plate = Least Value of Strength/(Tensile Stress*Pitch of Rivet*Efficiency of riveted joint)

Thickness of plates given crushing strength for 'n' number of rivets

Go Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)

Thickness of plate given tearing strength of rivet

Go Thickness of Plate = Tearing strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter))

Thickness of plate given strength of solid plate per pitch length

Go Thickness of Plate = Strength of solid plate/(Tensile Stress*Pitch of Rivet)

Thickness of plates given crushing strength for double rivet

Go Thickness of Plate = Crushing strength/(2*Crushing stress*Rivet Diameter)

Thickness of plates given crushing strength for single rivet

Go Thickness of Plate = Crushing strength/(1*Crushing stress*Rivet Diameter)

Thickness of plates given crushing strength for triple-rivet

Go Thickness of Plate = Crushing strength/(3*Crushing stress*Rivet Diameter)

Thickness of plates given crushing strength for 'n' number of rivets Formula

Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter)
t_plate = P_c/(n*σ_c*D_rivet)

What is the difference between solid shank rivet and special rivet?

Two of the major types of rivets used in the aircraft are the common solid shank type, which must be driven using a bucking bar, and the special (blind) rivets, which may be installed where it is impossible to use a bucking bar. Solid shank rivets are generally used in repair work.

How to Calculate Thickness of plates given crushing strength for 'n' number of rivets?

Thickness of plates given crushing strength for 'n' number of rivets calculator uses Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter) to calculate the Thickness of Plate, The Thickness of plates given crushing strength for 'n' number of rivets formula is defined as the distance through an object, as distinct from width or height. Thickness of Plate is denoted by t_plate symbol.

How to calculate Thickness of plates given crushing strength for 'n' number of rivets using this online calculator? To use this online calculator for Thickness of plates given crushing strength for 'n' number of rivets, enter Crushing strength (P_c), Number of Rivets Per Pitch (n), Crushing stress (σ_c) & Rivet Diameter (D_rivet) and hit the calculate button. Here is how the Thickness of plates given crushing strength for 'n' number of rivets calculation can be explained with given input values -> 55555.56 = 6400/(2*2400000*0.018).

FAQ

What is Thickness of plates given crushing strength for 'n' number of rivets?

The Thickness of plates given crushing strength for 'n' number of rivets formula is defined as the distance through an object, as distinct from width or height and is represented as t_plate = P_c/(n*σ_c*D_rivet) or Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter). Crushing strength is the capacity of a material or structure to withstand loads tending to reduce size, Number of Rivets Per Pitch is defined as total number of rivets that are present on the pitch of the rivet, Crushing stress is a special type of localized compressive stress which occurs at the surface of contact of two members that are relatively at rest & Rivet Diameter is offered from 1/16-inch (1.6 mm) to 3/8-inch (9.5 mm) in diameter (other sizes are considered highly special) and can be up to 8 inches (203 mm) long.

How to calculate Thickness of plates given crushing strength for 'n' number of rivets?

The Thickness of plates given crushing strength for 'n' number of rivets formula is defined as the distance through an object, as distinct from width or height is calculated using Thickness of Plate = Crushing strength/(Number of Rivets Per Pitch*Crushing stress*Rivet Diameter). To calculate Thickness of plates given crushing strength for 'n' number of rivets, you need Crushing strength (P_c), Number of Rivets Per Pitch (n), Crushing stress (σ_c) & Rivet Diameter (D_rivet). With our tool, you need to enter the respective value for Crushing strength, Number of Rivets Per Pitch, Crushing stress & Rivet Diameter and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickness of Plate?

In this formula, Thickness of Plate uses Crushing strength, Number of Rivets Per Pitch, Crushing stress & Rivet Diameter. We can use 6 other way(s) to calculate the same, which is/are as follows -

Thickness of Plate = Least Value of Strength/(Tensile Stress*Pitch of Rivet*Efficiency of riveted joint)
Thickness of Plate = Strength of solid plate/(Tensile Stress*Pitch of Rivet)
Thickness of Plate = Tearing strength/(Tensile Stress*(Pitch of Rivet-Rivet Diameter))
Thickness of Plate = Crushing strength/(2*Crushing stress*Rivet Diameter)
Thickness of Plate = Crushing strength/(1*Crushing stress*Rivet Diameter)
Thickness of Plate = Crushing strength/(3*Crushing stress*Rivet Diameter)

Home

FREE PDFs

🔍 Search