Actual Tension when Tension Correction to Measured Length is Given Calculator

Category	Engineering ↺
Engineering	Civil ↺
Civil	Surveying Formulas ↺
Surveying-Formulas	Measurement of Distance with Tapes ↺
Measurement-Of-Distance-With-Tapes

✖Initial tension at which tape is standardized.ⓘ Initial tension [P_i]			+10% -10%
✖Tension correction to measured length.ⓘ Tension correction [C_p]			+10% -10%
✖The area of tape is actually the cross section area of tape.ⓘ Area of tape [A]			+10% -10%
✖The modulus of elasticity of a material is a measure of its stiffnessⓘ Modulus of elasticity [E_s]			+10% -10%
✖The measured length is the length measured from steel tape during observation.ⓘ Measured length [s]			+10% -10%

✖The final tension is the actual tension applied during observation.ⓘ Actual Tension when Tension Correction to Measured Length is Given [P_f]

⎘ Copy

👎 Report Issue!

👍 Share Now!

You are here:

Home »
Engineering »
Civil »
Surveying Formulas »
Measurement of Distance with Tapes »
Actual Tension when Tension Correction to Measured Length is Given

Suraj Kumar

Birsa Institute of Technology (BIT), Sindri

Suraj Kumar has created this Calculator and 400+ more calculators!

Ishita Goyal

Meerut Institute of Engineering and Technology (MIET), Meerut

Ishita Goyal has verified this Calculator and 400+ more calculators!

< 11 Other formulas that you can solve using the same Inputs

Tension Correction to Measured Length

Tension correction=(((Final tension-Initial tension)*Measured length)/(Area of tape*Modulus of elasticity)) GO

Tape Cross-Sectional Area when Tension Correction to Measured Length is Given

Area of tape=((Final tension-Initial tension)*Measured length)/(Tension correction*modulus of elasticity) GO

Tape Standardized Tension when Tension Correction to Measured Length is Given

Initial tension=(Final tension-((Tension correction*Area of tape*Modulus of elasticity)/Measured length)) GO

Tape Elasticity Modulus when Tension Correction to Measured Length is Given

Modulus of elasticity=((Final tension-Initial tension)*Measured length)/(Tension correction*Area of tape) GO

Measured Length when Tension Correction to Measured Length is Given

Measured length=(Tension correction*Area of tape*Modulus of elasticity)/(Final tension-Initial tension) GO

Tape Weight when Sag Correction of Unsupported Tape is Given

Weight of tape per unit length=((Sag correction*24*(Initial tension^2))/(Unsupported length^3))^(1/2) GO

Unsupported Length when Sag Correction of Unsupported Tape is Given

Unsupported length=((Sag correction*24*Initial tension^2)/(Weight of tape per unit length^2))^(1/3) GO

Sag Correction of Unsupported Tape

Sag correction=((Weight of tape per unit length^2)*(Unsupported length^3))/(24*(Initial tension^2)) GO

Correction to be Subtracted from Slope Distance when Difference in Elevation is Given

Correction to be subtracted from slope distance=(Difference in elevation)^2/(2*Measured length) GO

Temperature Correction to Measured Length

Temperature correction=(0.0000065*Measured length*(Final temperature-Initial temperature)) GO

Correction to be Subtracted from Slope Distance

Correction to be subtracted from slope distance=(Measured length*(1-cos(Slope angle))) GO

Actual Tension when Tension Correction to Measured Length is Given Formula

Final tension=(Initial tension+((Tension correction*Area of tape*Modulus of elasticity)/Measured length))
Pf=(Pi+((Cp*A*Es)/s))

More formulas

Temperature Correction to Measured Length GO

Measured Length when Temperature Correction is Given GO

Correction to be Subtracted from Slope Distance GO

Measured Length when Correction to be Subtracted from Slope Distance is Given GO

Correction to be Subtracted from Slope Distance when Difference in Elevation is Given GO

Tension Correction to Measured Length GO

Measured Length when Tension Correction to Measured Length is Given GO

Tape Cross-Sectional Area when Tension Correction to Measured Length is Given GO

Tape Standardized Tension when Tension Correction to Measured Length is Given GO

Tape Elasticity Modulus when Tension Correction to Measured Length is Given GO

Sag Correction of Unsupported Tape GO

Tape Weight when Sag Correction of Unsupported Tape is Given GO

Unsupported Length when Sag Correction of Unsupported Tape is Given GO

Actual Tension when Sag Correction of Unsupported Tape is Given GO

What is tension correction?

The correction that must be applied to a tape if it is being used at a tension different from that at which it was standardized.

How to Calculate Actual Tension when Tension Correction to Measured Length is Given?

Actual Tension when Tension Correction to Measured Length is Given calculator uses Final tension=(Initial tension+((Tension correction*Area of tape*Modulus of elasticity)/Measured length)) to calculate the Final tension, The Actual Tension when Tension Correction to Measured Length is Given formula gives the value of tension that is applied during measurement. Final tension and is denoted by P_f symbol.

How to calculate Actual Tension when Tension Correction to Measured Length is Given using this online calculator? To use this online calculator for Actual Tension when Tension Correction to Measured Length is Given, enter Initial tension (P_i), Tension correction (C_p), Area of tape (A), Modulus of elasticity (E_s) and Measured length (s) and hit the calculate button. Here is how the Actual Tension when Tension Correction to Measured Length is Given calculation can be explained with given input values -> 6.000E+11 = (6+((6*5*200000000000)/10)).

FAQ

What is Actual Tension when Tension Correction to Measured Length is Given?

The Actual Tension when Tension Correction to Measured Length is Given formula gives the value of tension that is applied during measurement and is represented as P_f=(P_i+((C_p*A*E_s)/s)) or Final tension=(Initial tension+((Tension correction*Area of tape*Modulus of elasticity)/Measured length)). Initial tension at which tape is standardized, Tension correction to measured length, The area of tape is actually the cross section area of tape, The modulus of elasticity of a material is a measure of its stiffness and The measured length is the length measured from steel tape during observation.

How to calculate Actual Tension when Tension Correction to Measured Length is Given?

The Actual Tension when Tension Correction to Measured Length is Given formula gives the value of tension that is applied during measurement is calculated using Final tension=(Initial tension+((Tension correction*Area of tape*Modulus of elasticity)/Measured length)). To calculate Actual Tension when Tension Correction to Measured Length is Given, you need Initial tension (P_i), Tension correction (C_p), Area of tape (A), Modulus of elasticity (E_s) and Measured length (s). With our tool, you need to enter the respective value for Initial tension, Tension correction, Area of tape, Modulus of elasticity and Measured length and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Facebook
Twitter
WhatsApp
Reddit
LinkedIn
E-Mail

Let Others Know

✖

Facebook

Twitter

Copied!