Depth of machined surface given taper Calculator

✖Larger diameter is the bigger diameter of hole or other things.ⓘ Larger Diameter [D_sd]			+10% -10%
✖The smaller diameter is the smaller of all diameters of a given object.ⓘ Smaller Diameter [d]			+10% -10%
✖Taper produced in EDM is the taper produced due to side sparks during EDM.ⓘ Taper Produced in EDM [T_sd]			+10% -10%

✖Depth of machined surface is the how deep a surface is machined from the un-machined surface.ⓘ Depth of machined surface given taper [H_sd]

⎘ Copy

👎

Formula

✖

Depth of machined surface given taper

Formula

`"H"_{"sd"} = ("D"_{"sd"}-"d")/(2*"T"_{"sd"})`

Example

`"52m"=("22m"-"1.2m")/(2*"0.2")`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Depth of machined surface given taper Solution

STEP 0: Pre-Calculation Summary

Formula Used

Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM)
H_sd = (D_sd-d)/(2*T_sd)
This formula uses 4 Variables

Variables Used

Depth of Machined Surface - (Measured in Meter) - Depth of machined surface is the how deep a surface is machined from the un-machined surface.
Larger Diameter - (Measured in Meter) - Larger diameter is the bigger diameter of hole or other things.
Smaller Diameter - (Measured in Meter) - The smaller diameter is the smaller of all diameters of a given object.
Taper Produced in EDM - Taper produced in EDM is the taper produced due to side sparks during EDM.

STEP 1: Convert Input(s) to Base Unit

Larger Diameter: 22 Meter --> 22 Meter No Conversion Required
Smaller Diameter: 1.2 Meter --> 1.2 Meter No Conversion Required
Taper Produced in EDM: 0.2 --> No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

H_sd = (D_sd-d)/(2*T_sd) --> (22-1.2)/(2*0.2)

Evaluating ... ...

H_sd = 52

STEP 3: Convert Result to Output's Unit

52 Meter --> No Conversion Required

FINAL ANSWER

52 Meter <-- Depth of Machined Surface

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Unconventional machining processes » Electro Discharge Machining (EDM) » Possible surface defects in EDM » Taper Formation » Depth of machined surface given taper

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Vaibhav Malani

National Institute of Technology (NIT), Tiruchirapalli

Vaibhav Malani has verified this Calculator and 200+ more calculators!

< 9 Taper Formation Calculators

Volume of crater made by electric spark

Go Volume of Crater = (pi/12)*Depth of Machined Surface*((Smaller Diameter^2)+(Larger Diameter^2)+(Larger Diameter*Smaller Diameter))

Empirical constant for taper

Go Empirical Constant = (Larger Diameter-Smaller Diameter)/(2*Depth of Machined Surface*Smaller Diameter^2)

Depth of machined surface

Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Empirical Constant*Smaller Diameter^2)

Upper diameter of hole

Go Larger Diameter = 2*Depth of Machined Surface*Empirical Constant*Smaller Diameter^2+Smaller Diameter

Depth of machined surface given taper

Go Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM)

Smaller diameter of crater given Taper

Go Smaller Diameter = Larger Diameter-2*Depth of Machined Surface*Taper Produced in EDM

Largest size of hole given taper

Go Larger Diameter = 2*Depth of Machined Surface*Taper Produced in EDM+Smaller Diameter

Smallest diameter of hole given empirical constant

Go Smaller Diameter = sqrt(Taper Produced in EDM/Empirical Constant)

Taper produced due to side sparks

Go Taper Produced in EDM = Empirical Constant*Smaller Diameter^2

Depth of machined surface given taper Formula

Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM)
H_sd = (D_sd-d)/(2*T_sd)

What factors affects surface finish during EDM ?

The amount of material removed and the surface finish produced is dependent upon the current in the spark. The material removed by the spark can be assumed to be a crater. The amount removed therefore will depend upon the crater depth, which is directly proportional to the current. Thus as the material removed increases and at the same time, the surface finish also decreases. However, decreasing the current in the spark, but increasing its frequency will improve the surface finish in view of the small crater size, but at the same time, the material removal rate can be maintained by increasing the frequency.

How to Calculate Depth of machined surface given taper?

Depth of machined surface given taper calculator uses Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM) to calculate the Depth of Machined Surface, Depth of machined surface given taper formula is defined as perpendicular distance between machined and un-machined surface during EDM. Depth of Machined Surface is denoted by H_sd symbol.

How to calculate Depth of machined surface given taper using this online calculator? To use this online calculator for Depth of machined surface given taper, enter Larger Diameter (D_sd), Smaller Diameter (d) & Taper Produced in EDM (T_sd) and hit the calculate button. Here is how the Depth of machined surface given taper calculation can be explained with given input values -> 52 = (22-1.2)/(2*0.2).

FAQ

What is Depth of machined surface given taper?

Depth of machined surface given taper formula is defined as perpendicular distance between machined and un-machined surface during EDM and is represented as H_sd = (D_sd-d)/(2*T_sd) or Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM). Larger diameter is the bigger diameter of hole or other things, The smaller diameter is the smaller of all diameters of a given object & Taper produced in EDM is the taper produced due to side sparks during EDM.

How to calculate Depth of machined surface given taper?

Depth of machined surface given taper formula is defined as perpendicular distance between machined and un-machined surface during EDM is calculated using Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Taper Produced in EDM). To calculate Depth of machined surface given taper, you need Larger Diameter (D_sd), Smaller Diameter (d) & Taper Produced in EDM (T_sd). With our tool, you need to enter the respective value for Larger Diameter, Smaller Diameter & Taper Produced in EDM and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Depth of Machined Surface?

In this formula, Depth of Machined Surface uses Larger Diameter, Smaller Diameter & Taper Produced in EDM. We can use 1 other way(s) to calculate the same, which is/are as follows -

Depth of Machined Surface = (Larger Diameter-Smaller Diameter)/(2*Empirical Constant*Smaller Diameter^2)

Home

FREE PDFs

🔍 Search