Supply Voltage given Specific Resistivity of Electrolyte Calculator

✖Specific Resistance of the electrolyte is the measure of how strongly it opposes the flow of current through them.ⓘ Specific Resistance of The Electrolyte [r_e]			+10% -10%
✖The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining.ⓘ Gap Between Tool and Work Surface [h]			+10% -10%
✖Electric current is the rate of flow of electric charge through a circuit, measured in amperes.ⓘ Electric Current [I]			+10% -10%
✖Area of Penetration is area of penetration of electrons.ⓘ Area of Penetration [A]			+10% -10%

✖Supply Voltage is the voltage required to charge a given device within a given time.ⓘ Supply Voltage given Specific Resistivity of Electrolyte [V_s]

⎘ Copy

👎

Formula

✖

Supply Voltage given Specific Resistivity of Electrolyte

Formula

`"V"_{"s"} = "r"_{"e"}*"h"*"I"/"A"`

Example

`"9.868421V"="3Ω*cm"*"0.25mm"*"1000A"/"7.6cm²"`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF

Supply Voltage given Specific Resistivity of Electrolyte Solution

STEP 0: Pre-Calculation Summary

Formula Used

Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration
V_s = r_e*h*I/A
This formula uses 5 Variables

Variables Used

Supply Voltage - (Measured in Volt) - Supply Voltage is the voltage required to charge a given device within a given time.
Specific Resistance of The Electrolyte - (Measured in Ohm Meter) - Specific Resistance of the electrolyte is the measure of how strongly it opposes the flow of current through them.
Gap Between Tool and Work Surface - (Measured in Meter) - The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining.
Electric Current - (Measured in Ampere) - Electric current is the rate of flow of electric charge through a circuit, measured in amperes.
Area of Penetration - (Measured in Square Meter) - Area of Penetration is area of penetration of electrons.

STEP 1: Convert Input(s) to Base Unit

Specific Resistance of The Electrolyte: 3 Ohm Centimeter --> 0.03 Ohm Meter (Check conversion here)
Gap Between Tool and Work Surface: 0.25 Millimeter --> 0.00025 Meter (Check conversion here)
Electric Current: 1000 Ampere --> 1000 Ampere No Conversion Required
Area of Penetration: 7.6 Square Centimeter --> 0.00076 Square Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

V_s = r_e*h*I/A --> 0.03*0.00025*1000/0.00076

Evaluating ... ...

V_s = 9.86842105263158

STEP 3: Convert Result to Output's Unit

9.86842105263158 Volt --> No Conversion Required

FINAL ANSWER

9.86842105263158 ≈ 9.868421 Volt <-- Supply Voltage

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Heat in Electrolyte » Supply Voltage given Specific Resistivity of Electrolyte

Credits

Created by Kumar Siddhant

Indian Institute of Information Technology, Design and Manufacturing (IIITDM), Jabalpur

Kumar Siddhant has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< 10+ Heat in Electrolyte Calculators

Ambient Temperature during ECM

Go Ambient Air Temperature = Boiling Point of Electrolyte-(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Maximum Volume Flow Rate)

Specific Heat of Electrolyte from Volume Flow Rate

Go Specific Heat Capacity of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Volume Flow Rate*(Boiling Point of Electrolyte-Ambient Air Temperature))

Boiling Point of Electrolyte during Electrochemical Machining of Metals

Go Boiling Point of Electrolyte = Ambient Air Temperature+(Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*Volume Flow Rate)

Ambient Temperature

Go Ambient Air Temperature = Boiling Point of Electrolyte-Heat Absorption of Electrolyte/(Maximum Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte)

Flow Rate of Electrolyte from Heat Absorbed Electrolyte

Go Volume Flow Rate = Heat Absorption of Electrolyte/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Density of Electrolyte from Heat Absorbed Electrolyte

Go Density of Electrolyte = Heat Absorption of Electrolyte/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Specific Heat of Electrolyte

Go Specific Heat Capacity of Electrolyte = Heat Absorption of Electrolyte/(Volume Flow Rate*Density of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Heat Absorbed by Electrolyte

Go Heat Absorption of Electrolyte = Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature)

Boiling Point of Electrolyte

Go Boiling Point of Electrolyte = Ambient Air Temperature+Heat Absorption of Electrolyte/(Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte)

Supply Voltage given Specific Resistivity of Electrolyte

Go Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration

Supply Voltage given Specific Resistivity of Electrolyte Formula

Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration
V_s = r_e*h*I/A

Voltage for ECM

The voltage is required to be applied for the electrochemical reaction to proceed at a steady-state. That voltage or potential difference is around 2 to 30 V. The applied potential
the difference, however, also overcomes the following resistances or potential drops.
1. The electrode potential
2. The activation overpotential
3. Ohmic potential drop
4. Concentration overpotential
5. Ohmic resistance of the electrolyte

How to Calculate Supply Voltage given Specific Resistivity of Electrolyte?

Supply Voltage given Specific Resistivity of Electrolyte calculator uses Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration to calculate the Supply Voltage, The Supply Voltage given Specific Resistivity of Electrolyte is a method to determine the Potential Difference across which the electrolysis is done for ECM when the Specific Resistivity of Electrolyte is known. Supply Voltage is denoted by V_s symbol.

How to calculate Supply Voltage given Specific Resistivity of Electrolyte using this online calculator? To use this online calculator for Supply Voltage given Specific Resistivity of Electrolyte, enter Specific Resistance of The Electrolyte (r_e), Gap Between Tool and Work Surface (h), Electric Current (I) & Area of Penetration (A) and hit the calculate button. Here is how the Supply Voltage given Specific Resistivity of Electrolyte calculation can be explained with given input values -> 9.868421 = 0.03*0.00025*1000/0.00076.

FAQ

What is Supply Voltage given Specific Resistivity of Electrolyte?

The Supply Voltage given Specific Resistivity of Electrolyte is a method to determine the Potential Difference across which the electrolysis is done for ECM when the Specific Resistivity of Electrolyte is known and is represented as V_s = r_e*h*I/A or Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration. Specific Resistance of the electrolyte is the measure of how strongly it opposes the flow of current through them, The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining, Electric current is the rate of flow of electric charge through a circuit, measured in amperes & Area of Penetration is area of penetration of electrons.

How to calculate Supply Voltage given Specific Resistivity of Electrolyte?

The Supply Voltage given Specific Resistivity of Electrolyte is a method to determine the Potential Difference across which the electrolysis is done for ECM when the Specific Resistivity of Electrolyte is known is calculated using Supply Voltage = Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface*Electric Current/Area of Penetration. To calculate Supply Voltage given Specific Resistivity of Electrolyte, you need Specific Resistance of The Electrolyte (r_e), Gap Between Tool and Work Surface (h), Electric Current (I) & Area of Penetration (A). With our tool, you need to enter the respective value for Specific Resistance of The Electrolyte, Gap Between Tool and Work Surface, Electric Current & Area of Penetration and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

Home

FREE PDFs

🔍 Search