Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin Calculator

✖Bending Moment in Knuckle Pin is the amount of bending moment acting onto the knuckle pin when the knuckle joint is subjected to axial loading.ⓘ Bending Moment in Knuckle Pin [M_b]			+10% -10%
✖Load on Knuckle Joint is basically the amount of load/force any part, product, or joint of a knuckle joint can bear or is acted upon or exerts.ⓘ Load on Knuckle Joint [L]			+10% -10%
✖Thickess of Eye of Knuckle Joint is the thickness of the eye of the nonforked part of the knuckle joint, measured perpendicular to the eye hole radius.ⓘ Thickess of Eye of Knuckle Joint [b]			+10% -10%

✖Thickess of Fork Eye of Knuckle Joint is the thickness of the eye of the forked part of the knuckle joint, measured perpendicular to the eye hole radius.ⓘ Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin [a]

⎘ Copy

👎

Formula

✖

Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin

Formula

`"a" = 3*(2*"M"_{"b"}/"L"-"b"/4)`

Example

`"24mm"=3*(2*"450000N*mm"/"50000N"-"40mm"/4)`

Calculator

LaTeX

Reset

👍

Download Design of Knuckle Joint Formulas PDF PDF Image

Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin Solution

STEP 0: Pre-Calculation Summary

Formula Used

Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4)
a = 3*(2*M_b/L-b/4)
This formula uses 4 Variables

Variables Used

Thickess of Fork Eye of Knuckle Joint - (Measured in Meter) - Thickess of Fork Eye of Knuckle Joint is the thickness of the eye of the forked part of the knuckle joint, measured perpendicular to the eye hole radius.
Bending Moment in Knuckle Pin - (Measured in Newton Meter) - Bending Moment in Knuckle Pin is the amount of bending moment acting onto the knuckle pin when the knuckle joint is subjected to axial loading.
Load on Knuckle Joint - (Measured in Newton) - Load on Knuckle Joint is basically the amount of load/force any part, product, or joint of a knuckle joint can bear or is acted upon or exerts.
Thickess of Eye of Knuckle Joint - (Measured in Meter) - Thickess of Eye of Knuckle Joint is the thickness of the eye of the nonforked part of the knuckle joint, measured perpendicular to the eye hole radius.

STEP 1: Convert Input(s) to Base Unit

Bending Moment in Knuckle Pin: 450000 Newton Millimeter --> 450 Newton Meter (Check conversion here)
Load on Knuckle Joint: 50000 Newton --> 50000 Newton No Conversion Required
Thickess of Eye of Knuckle Joint: 40 Millimeter --> 0.04 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

a = 3*(2*M_b/L-b/4) --> 3*(2*450/50000-0.04/4)

Evaluating ... ...

a = 0.024

STEP 3: Convert Result to Output's Unit

0.024 Meter -->24 Millimeter (Check conversion here)

FINAL ANSWER

24 Millimeter <-- Thickess of Fork Eye of Knuckle Joint

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Design of Machine Elements » Design of Coupling » Design of Knuckle Joint » Fork » Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin

Credits

Created by Saurabh Patil

Shri Govindram Seksaria Institute of Technology and Science (SGSITS ), Indore

Saurabh Patil has created this Calculator and 700+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< 11 Fork Calculators

Thickness of Fork Eye of Knuckle Joint given Bending Stress in Pin

Go Thickess of Fork Eye of Knuckle Joint = 3*((pi*Diameter of Knuckle Pin^3*Bending Stress in Knuckle Pin)/(16*Load on Knuckle Joint)-Thickess of Eye of Knuckle Joint/4)

Thickness of Fork Eye of Knuckle Joint given Tensile Stress in Fork

Go Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Tensile Stress in Fork of Knuckle Joint*(Outer Diameter of Eye of Knuckle Joint-Diameter of Knuckle Pin))

Outer Diameter of Eye of Knuckle Joint given Tensile Stress in Fork

Go Outer Diameter of Eye of Knuckle Joint = Load on Knuckle Joint/(2*Tensile Stress in Fork of Knuckle Joint*Thickess of Fork Eye of Knuckle Joint)+Diameter of Knuckle Pin

Thickness of Fork Eye of Knuckle Joint given Shear Stress in Fork

Go Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Shear Stress in Fork of Knuckle Joint*(Outer Diameter of Eye of Knuckle Joint-Diameter of Knuckle Pin))

Outer Diameter of Eye of Knuckle Joint given Shear Stress in Fork

Go Outer Diameter of Eye of Knuckle Joint = Load on Knuckle Joint/(2*Shear Stress in Fork of Knuckle Joint*Thickess of Fork Eye of Knuckle Joint)+Diameter of Knuckle Pin

Outer Diameter of Eye of Knuckle Joint given Tensile Stress in Eye

Go Outer Diameter of Eye of Knuckle Joint = Diameter of Knuckle Pin+Load on Knuckle Joint/(Thickess of Eye of Knuckle Joint*Tensile Stress in Eye of Knuckle Joint)

Outer Diameter of Eye of Knuckle Joint given Shear Stress in Eye

Go Outer Diameter of Eye of Knuckle Joint = Diameter of Knuckle Pin+Load on Knuckle Joint/(Thickess of Eye of Knuckle Joint*Shear Stress in Eye of Knuckle Joint)

Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin

Go Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4)

Thickness of Fork Eye of Knuckle Joint given Compressive Stress in Pin Inside Fork End

Go Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Compressive Stress in Knuckle Pin*Diameter of Knuckle Pin)

Thickness of Fork Eye of Knuckle Joint given Rod Diameter

Go Thickess of Fork Eye of Knuckle Joint = 0.75*Diameter of Rod of Knuckle Joint

Outer Diameter of Eye of Knuckle Joint given Diameter of Pin

Go Outer Diameter of Eye of Knuckle Joint = 2*Diameter of Knuckle Pin

Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin Formula

Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4)
a = 3*(2*M_b/L-b/4)

What is a knuckle joint?

A knuckle joint is used to connect the two rods which are under the tensile load when there is a requirement for a small amount of flexibility or when angular movement is necessary. There is always an axial or linear line of action of load.
The knuckle joint assembly consists of the following major components:
Single eye.
Double-eye or fork
Knuckle pin.

How to Calculate Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin?

Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin calculator uses Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4) to calculate the Thickess of Fork Eye of Knuckle Joint, Thickness of fork eye of knuckle joint given bending moment in pin is the thickness of the eye of the fork part of a knuckle joint and is measured along the eye hole axis. Thickess of Fork Eye of Knuckle Joint is denoted by a symbol.

How to calculate Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin using this online calculator? To use this online calculator for Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin, enter Bending Moment in Knuckle Pin (M_b), Load on Knuckle Joint (L) & Thickess of Eye of Knuckle Joint (b) and hit the calculate button. Here is how the Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin calculation can be explained with given input values -> 24000 = 3*(2*450/50000-0.04/4).

FAQ

What is Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin?

Thickness of fork eye of knuckle joint given bending moment in pin is the thickness of the eye of the fork part of a knuckle joint and is measured along the eye hole axis and is represented as a = 3*(2*M_b/L-b/4) or Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4). Bending Moment in Knuckle Pin is the amount of bending moment acting onto the knuckle pin when the knuckle joint is subjected to axial loading, Load on Knuckle Joint is basically the amount of load/force any part, product, or joint of a knuckle joint can bear or is acted upon or exerts & Thickess of Eye of Knuckle Joint is the thickness of the eye of the nonforked part of the knuckle joint, measured perpendicular to the eye hole radius.

How to calculate Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin?

Thickness of fork eye of knuckle joint given bending moment in pin is the thickness of the eye of the fork part of a knuckle joint and is measured along the eye hole axis is calculated using Thickess of Fork Eye of Knuckle Joint = 3*(2*Bending Moment in Knuckle Pin/Load on Knuckle Joint-Thickess of Eye of Knuckle Joint/4). To calculate Thickness of Fork Eye of Knuckle Joint given Bending Moment in Pin, you need Bending Moment in Knuckle Pin (M_b), Load on Knuckle Joint (L) & Thickess of Eye of Knuckle Joint (b). With our tool, you need to enter the respective value for Bending Moment in Knuckle Pin, Load on Knuckle Joint & Thickess of Eye of Knuckle Joint and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Thickess of Fork Eye of Knuckle Joint?

In this formula, Thickess of Fork Eye of Knuckle Joint uses Bending Moment in Knuckle Pin, Load on Knuckle Joint & Thickess of Eye of Knuckle Joint. We can use 5 other way(s) to calculate the same, which is/are as follows -

Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Compressive Stress in Knuckle Pin*Diameter of Knuckle Pin)
Thickess of Fork Eye of Knuckle Joint = 3*((pi*Diameter of Knuckle Pin^3*Bending Stress in Knuckle Pin)/(16*Load on Knuckle Joint)-Thickess of Eye of Knuckle Joint/4)
Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Tensile Stress in Fork of Knuckle Joint*(Outer Diameter of Eye of Knuckle Joint-Diameter of Knuckle Pin))
Thickess of Fork Eye of Knuckle Joint = Load on Knuckle Joint/(2*Shear Stress in Fork of Knuckle Joint*(Outer Diameter of Eye of Knuckle Joint-Diameter of Knuckle Pin))
Thickess of Fork Eye of Knuckle Joint = 0.75*Diameter of Rod of Knuckle Joint

Home

FREE PDFs

🔍 Search