Length of Weld given Tensile Strength of Double Fillet Lap Calculator

✖Tensile strength is the stress at the maximum on the engineering stress-strain curve.ⓘ Tensile Strength [TS]			+10% -10%
✖Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.ⓘ Tensile Stress [σ_t]			+10% -10%
✖The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.ⓘ Thickness of Plate [t_plate]			+10% -10%

✖The Length of Weld is the linear distance of each weld segment.ⓘ Length of Weld given Tensile Strength of Double Fillet Lap [l]

⎘ Copy

👎

Formula

✖

Length of Weld given Tensile Strength of Double Fillet Lap

Formula

`"l" = "TS"/(1.414*"σ"_{"t"}*"t"_{"plate"})`

Example

`"64459.57mm"="35MPa"/(1.414*"32MPa"*"12mm")`

Calculator

LaTeX

Reset

👍

Download Strength of Materials Formula PDF PDF Image

Length of Weld given Tensile Strength of Double Fillet Lap Solution

STEP 0: Pre-Calculation Summary

Formula Used

Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate)
l = TS/(1.414*σ_t*t_plate)
This formula uses 4 Variables

Variables Used

Length of Weld - (Measured in Meter) - The Length of Weld is the linear distance of each weld segment.
Tensile Strength - (Measured in Pascal) - Tensile strength is the stress at the maximum on the engineering stress-strain curve.
Tensile Stress - (Measured in Pascal) - Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.
Thickness of Plate - (Measured in Meter) - The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

STEP 1: Convert Input(s) to Base Unit

Tensile Strength: 35 Megapascal --> 35000000 Pascal (Check conversion here)
Tensile Stress: 32 Megapascal --> 32000000 Pascal (Check conversion here)
Thickness of Plate: 12 Millimeter --> 0.012 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

l = TS/(1.414*σ_t*t_plate) --> 35000000/(1.414*32000000*0.012)

Evaluating ... ...

l = 64.4595709570957

STEP 3: Convert Result to Output's Unit

64.4595709570957 Meter -->64459.5709570957 Millimeter (Check conversion here)

FINAL ANSWER

64459.5709570957 ≈ 64459.57 Millimeter <-- Length of Weld

(Calculation completed in 00.004 seconds)

You are here -

Home » Physics » Strength of Materials » Welded Joints » Types of Welded Joints » Length of Weld » Length of Weld given Tensile Strength of Double Fillet Lap

Credits

Created by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has created this Calculator and 2000+ more calculators!

Verified by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has verified this Calculator and 1900+ more calculators!

< 9 Length of Weld Calculators

Length of Weld given Tensile Strength of Single Fillet Lap Joint

Go Length of Weld = Tensile Strength/(0.707*Tensile Stress*Thickness of Plate)

Length of Weld given Tensile Strength of Double Fillet Lap

Go Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate)

Length of Weld given Tensile Force for Butt Weld Joint

Go Length of Weld = Tensile Force in Butt Weld/(Tensile Stress*Depth of Weld)

Length of Weld given Area of Fillet Weld for Double Fillet Lap Joint

Go Length of Weld = Weld Bed Area/(1.414*Thickness of Plate)

Length of Weld given Area of Fillet Weld for Single Fillet Lap Joint

Go Length of Weld = Weld Bed Area/(0.707*Thickness of Plate)

Length of Weld given Area of Parallel Fillet Weld

Go Length of Weld = Weld Bed Area/(1.414*Thickness of Plate)

Length of Weld given Area of Fillet Weld and Throat Thickness for Double Fillet Lap Joint

Go Length of Weld = Weld Bed Area/(2*Throat Thickness)

Length of Weld given Area of Parallel Fillet Weld and Throat Thickness

Go Length of Weld = Weld Bed Area/(2*Throat Thickness)

Length of Weld given Area of Fillet Weld and Throat Thickness for Single Fillet Lap Joint

Go Length of Weld = Weld Bed Area/Throat Thickness

Length of Weld given Tensile Strength of Double Fillet Lap Formula

Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate)
l = TS/(1.414*σ_t*t_plate)

What is tensile strength with example?

Tensile strength is a measurement of the force required to pull something such as rope, wire, or a structural beam to the point where it breaks. The tensile strength of a material is the maximum amount of tensile stress that it can take before failure, for example, breaking.

How to Calculate Length of Weld given Tensile Strength of Double Fillet Lap?

Length of Weld given Tensile Strength of Double Fillet Lap calculator uses Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate) to calculate the Length of Weld, The Length of weld given tensile strength of double fillet lap formula is defined as the linear distance of each weld segment. Length of Weld is denoted by l symbol.

How to calculate Length of Weld given Tensile Strength of Double Fillet Lap using this online calculator? To use this online calculator for Length of Weld given Tensile Strength of Double Fillet Lap, enter Tensile Strength (TS), Tensile Stress (σ_t) & Thickness of Plate (t_plate) and hit the calculate button. Here is how the Length of Weld given Tensile Strength of Double Fillet Lap calculation can be explained with given input values -> 6.4E+7 = 35000000/(1.414*32000000*0.012).

FAQ

What is Length of Weld given Tensile Strength of Double Fillet Lap?

The Length of weld given tensile strength of double fillet lap formula is defined as the linear distance of each weld segment and is represented as l = TS/(1.414*σ_t*t_plate) or Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate). Tensile strength is the stress at the maximum on the engineering stress-strain curve, Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force & The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

How to calculate Length of Weld given Tensile Strength of Double Fillet Lap?

The Length of weld given tensile strength of double fillet lap formula is defined as the linear distance of each weld segment is calculated using Length of Weld = Tensile Strength/(1.414*Tensile Stress*Thickness of Plate). To calculate Length of Weld given Tensile Strength of Double Fillet Lap, you need Tensile Strength (TS), Tensile Stress (σ_t) & Thickness of Plate (t_plate). With our tool, you need to enter the respective value for Tensile Strength, Tensile Stress & Thickness of Plate and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Length of Weld?

In this formula, Length of Weld uses Tensile Strength, Tensile Stress & Thickness of Plate. We can use 8 other way(s) to calculate the same, which is/are as follows -

Length of Weld = Weld Bed Area/(2*Throat Thickness)
Length of Weld = Weld Bed Area/Throat Thickness
Length of Weld = Weld Bed Area/(1.414*Thickness of Plate)
Length of Weld = Weld Bed Area/(0.707*Thickness of Plate)
Length of Weld = Weld Bed Area/(1.414*Thickness of Plate)
Length of Weld = Weld Bed Area/(2*Throat Thickness)
Length of Weld = Tensile Force in Butt Weld/(Tensile Stress*Depth of Weld)
Length of Weld = Tensile Strength/(0.707*Tensile Stress*Thickness of Plate)

Home

FREE PDFs

🔍 Search