Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal Calculator

✖Output resistance refers to the resistance of an electronic circuit to the flow of current when a load is connected to its output.ⓘ Output Resistance [R_out]			+10% -10%
✖Transconductance is defined as the ratio of the change in the output current to the change in the input voltage, with the gate-source voltage held constant.ⓘ Transconductance [g_m]			+10% -10%
✖A common mode input signal is a type of electrical signal that appears equally on both input terminals of a differential amplifier.ⓘ Common Mode Input Signal [V_cin]			+10% -10%

✖Drain Voltage Q1 is voltage taken at Drain terminal at one transistor Q1 in Differential Circuit.ⓘ Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal [v_o1]

⎘ Copy

👎

Formula

✖

Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal

Formula

`"v"_{"o1"} = -"R"_{"out"}*("g"_{"m"}*"V"_{"cin"})/(1+(2*"g"_{"m"}*"R"_{"out"}))`

Example

`"-34.65V"=-"4.5kΩ"*("0.5mS"*"84.7V")/(1+(2*"0.5mS"*"4.5kΩ"))`

Calculator

LaTeX

Reset

👍

Download MOSFET Formula PDF PDF Image

Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal Solution

STEP 0: Pre-Calculation Summary

Formula Used

Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance))
v_o1 = -R_out*(g_m*V_cin)/(1+(2*g_m*R_out))
This formula uses 4 Variables

Variables Used

Drain Voltage Q1 - (Measured in Volt) - Drain Voltage Q1 is voltage taken at Drain terminal at one transistor Q1 in Differential Circuit.
Output Resistance - (Measured in Ohm) - Output resistance refers to the resistance of an electronic circuit to the flow of current when a load is connected to its output.
Transconductance - (Measured in Siemens) - Transconductance is defined as the ratio of the change in the output current to the change in the input voltage, with the gate-source voltage held constant.
Common Mode Input Signal - (Measured in Volt) - A common mode input signal is a type of electrical signal that appears equally on both input terminals of a differential amplifier.

STEP 1: Convert Input(s) to Base Unit

Output Resistance: 4.5 Kilohm --> 4500 Ohm (Check conversion here)
Transconductance: 0.5 Millisiemens --> 0.0005 Siemens (Check conversion here)
Common Mode Input Signal: 84.7 Volt --> 84.7 Volt No Conversion Required

STEP 2: Evaluate Formula

Substituting Input Values in Formula

v_o1 = -R_out*(g_m*V_cin)/(1+(2*g_m*R_out)) --> -4500*(0.0005*84.7)/(1+(2*0.0005*4500))

Evaluating ... ...

v_o1 = -34.65

STEP 3: Convert Result to Output's Unit

-34.65 Volt --> No Conversion Required

FINAL ANSWER

-34.65 Volt <-- Drain Voltage Q1

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Electronics » MOSFET » Analog Electronics » Voltage » Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal

Credits

Created by Payal Priya

Birsa Institute of Technology (BIT), Sindri

Payal Priya has created this Calculator and 600+ more calculators!

Verified by Anshika Arya

National Institute Of Technology (NIT), Hamirpur

Anshika Arya has verified this Calculator and 2500+ more calculators!

< 20 Voltage Calculators

Conductance of Channel of MOSFET using Gate to Source Voltage

Go Conductance of Channel = Mobility of Electrons at Surface of Channel*Oxide Capacitance*Channel Width/Channel Length*(Gate-Source Voltage-Threshold Voltage)

Common Gate Output Voltage

Go Output Voltage = -(Transconductance*Critical Voltage)*((Load Resistance*Gate Resistance)/(Gate Resistance+Load Resistance))

Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal

Go Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance))

Voltage across Gate and Source of MOSFET on Operation with Differential Input Voltage

Go Gate-Source Voltage = Threshold Voltage+sqrt((2*DC Bias Current)/(Process Transconductance Parameter*Aspect Ratio))

Source Input Voltage

Go Source Input Voltage = Input Voltage*(Input Amplifier Resistance/(Input Amplifier Resistance+Equivalent Source Resistance))

Input Gate-to-Source Voltage

Go Critical Voltage = (Input Amplifier Resistance/(Input Amplifier Resistance+Equivalent Source Resistance))*Input Voltage

Output Voltage at Drain Q2 of MOSFET given Common-Mode Signal

Go Drain Voltage Q2 = -(Output Resistance/((1/Transconductance)+2*Output Resistance))*Common Mode Input Signal

Voltage across Gate and Source of MOSFET given Input Current

Go Gate-Source Voltage = Input Current/(Angular Frequency*(Source Gate Capacitance+Gate-Drain Capacitance))

Positive Voltage given Device Parameter in MOSFET

Go Input Current = Gate-Source Voltage*(Angular Frequency*(Source Gate Capacitance+Gate-Drain Capacitance))

Overdrive Voltage when MOSFET Acts as Amplifier with Load Resistance

Go Transconductance = Total Current/(Common Mode Input Signal-(2*Total Current*Output Resistance))

Incremental Voltage Signal of Differential Amplifier

Go Common Mode Input Signal = (Total Current/Transconductance)+(2*Total Current*Output Resistance)

Voltage at Drain Q1 of MOSFET

Go Output Voltage = -(Total Load Resistance of MOSFET/(2*Output Resistance))*Common Mode Input Signal

Voltage at Drain Q2 in MOSFET

Go Output Voltage = -(Total Load Resistance of MOSFET/(2*Output Resistance))*Common Mode Input Signal

Saturation Voltage of MOSFET

Go Drain and Source Saturation Voltage = Gate-Source Voltage-Threshold Voltage

Voltage across Gate to Source of MOSFET on Differential Input Voltage given Overdrive Voltage

Go Gate-Source Voltage = Threshold Voltage+1.4*Effective Voltage

Threshold Voltage when MOSFET Acts as Amplifier

Go Threshold Voltage = Gate-Source Voltage-Effective Voltage

Treshold Voltage of MOSFET

Go Threshold Voltage = Gate-Source Voltage-Effective Voltage

Overdrive Voltage

Go Overdrive Voltage = (2*Drain Current)/Transconductance

Output Voltage at Drain Q1 of MOSFET

Go Drain Voltage Q1 = -(Output Resistance*Total Current)

Output Voltage at Drain Q2 of MOSFET

Go Drain Voltage Q2 = -(Output Resistance*Total Current)

Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal Formula

Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance))
v_o1 = -R_out*(g_m*V_cin)/(1+(2*g_m*R_out))

What does common mode rejection do?

Common-mode rejection is the ability of the differential amplifier (which sits between the oscilloscope and probes as a signal-conditioning preamp) to eliminate the common-mode voltage from the output. But as signal frequencies rise, CMRR deteriorates.

How to Calculate Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal?

Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal calculator uses Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance)) to calculate the Drain Voltage Q1, The Output voltage at drain Q1 of MOSFET given common-mode signal formula is defined as is the voltage released by a device, such as a voltage regulator or a generator. Drain Voltage Q1 is denoted by v_o1 symbol.

How to calculate Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal using this online calculator? To use this online calculator for Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal, enter Output Resistance (R_out), Transconductance (g_m) & Common Mode Input Signal (V_cin) and hit the calculate button. Here is how the Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal calculation can be explained with given input values -> -34.65 = -4500*(0.0005*84.7)/(1+(2*0.0005*4500)).

FAQ

What is Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal?

The Output voltage at drain Q1 of MOSFET given common-mode signal formula is defined as is the voltage released by a device, such as a voltage regulator or a generator and is represented as v_o1 = -R_out*(g_m*V_cin)/(1+(2*g_m*R_out)) or Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance)). Output resistance refers to the resistance of an electronic circuit to the flow of current when a load is connected to its output, Transconductance is defined as the ratio of the change in the output current to the change in the input voltage, with the gate-source voltage held constant & A common mode input signal is a type of electrical signal that appears equally on both input terminals of a differential amplifier.

How to calculate Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal?

The Output voltage at drain Q1 of MOSFET given common-mode signal formula is defined as is the voltage released by a device, such as a voltage regulator or a generator is calculated using Drain Voltage Q1 = -Output Resistance*(Transconductance*Common Mode Input Signal)/(1+(2*Transconductance*Output Resistance)). To calculate Output Voltage at Drain Q1 of MOSFET given Common-Mode Signal, you need Output Resistance (R_out), Transconductance (g_m) & Common Mode Input Signal (V_cin). With our tool, you need to enter the respective value for Output Resistance, Transconductance & Common Mode Input Signal and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Drain Voltage Q1?

In this formula, Drain Voltage Q1 uses Output Resistance, Transconductance & Common Mode Input Signal. We can use 1 other way(s) to calculate the same, which is/are as follows -

Drain Voltage Q1 = -(Output Resistance*Total Current)

Home

FREE PDFs

🔍 Search