Specific Resistance of Electrolyte Calculator

✖Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.ⓘ Resistance of Gap Between Work and Tool [R]			+10% -10%
✖The Cross Sectional Area of Gap is defined as the cross-sectional area of the equilibrium gap which is required to maintain the desired electrolytic effect between tool and workpiece.ⓘ Cross Sectional Area of Gap [A_Gap]			+10% -10%
✖The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining.ⓘ Gap Between Tool and Work Surface [h]			+10% -10%

✖Specific Resistance of the electrolyte is the measure of how strongly it opposes the flow of current through them.ⓘ Specific Resistance of Electrolyte [r_e]

⎘ Copy

👎

Formula

✖

Specific Resistance of Electrolyte

Formula

`"r"_{"e"} = ("R"*"A"_{"Gap"})/"h"`

Example

`"3Ω*cm"=("0.012Ω"*"6.25cm²")/"0.25mm"`

Calculator

LaTeX

Reset

👍

Download Production Engineering Formula PDF PDF Image

Specific Resistance of Electrolyte Solution

STEP 0: Pre-Calculation Summary

Formula Used

Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface
r_e = (R*A_Gap)/h
This formula uses 4 Variables

Variables Used

Specific Resistance of The Electrolyte - (Measured in Ohm Meter) - Specific Resistance of the electrolyte is the measure of how strongly it opposes the flow of current through them.
Resistance of Gap Between Work and Tool - (Measured in Ohm) - Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry.
Cross Sectional Area of Gap - (Measured in Square Meter) - The Cross Sectional Area of Gap is defined as the cross-sectional area of the equilibrium gap which is required to maintain the desired electrolytic effect between tool and workpiece.
Gap Between Tool and Work Surface - (Measured in Meter) - The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining.

STEP 1: Convert Input(s) to Base Unit

Resistance of Gap Between Work and Tool: 0.012 Ohm --> 0.012 Ohm No Conversion Required
Cross Sectional Area of Gap: 6.25 Square Centimeter --> 0.000625 Square Meter (Check conversion here)
Gap Between Tool and Work Surface: 0.25 Millimeter --> 0.00025 Meter (Check conversion here)

STEP 2: Evaluate Formula

Substituting Input Values in Formula

r_e = (R*A_Gap)/h --> (0.012*0.000625)/0.00025

Evaluating ... ...

r_e = 0.03

STEP 3: Convert Result to Output's Unit

0.03 Ohm Meter -->3 Ohm Centimeter (Check conversion here)

FINAL ANSWER

3 Ohm Centimeter <-- Specific Resistance of The Electrolyte

(Calculation completed in 00.004 seconds)

You are here -

Home » Engineering » Production Engineering » Metal Machining » Electrochemical Machining » Gap Resistance » Specific Resistance of Electrolyte

Credits

Created by Rajat Vishwakarma

University Institute of Technology RGPV (UIT - RGPV), Bhopal

Rajat Vishwakarma has created this Calculator and 400+ more calculators!

Verified by Parul Keshav

National Institute of Technology (NIT), Srinagar

Parul Keshav has verified this Calculator and 400+ more calculators!

< 14 Gap Resistance Calculators

Flow Rate of Electrolytes from Gap Resistance ECM

Go Volume Flow Rate = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Density of Electrolyte

Go Density of Electrolyte = (Electric Current^2*Resistance of Gap Between Work and Tool)/(Volume Flow Rate*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))

Gap Resistance from Electrolyte Flow Rate

Go Resistance of Gap Between Work and Tool = (Volume Flow Rate*Density of Electrolyte*Specific Heat Capacity of Electrolyte*(Boiling Point of Electrolyte-Ambient Air Temperature))/Electric Current^2

Specific Resistivity of Electrolyte given Gap between Tool and Work Surface

Go Specific Resistance of The Electrolyte = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Gap Between Tool and Work Surface*Work Piece Density*Feed Speed)

Density of Work Material given Gap between Tool and Work Surface

Go Work Piece Density = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Feed Speed*Gap Between Tool and Work Surface)

Tool Feed Speed given Gap between Tool and Work Surface

Go Feed Speed = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Gap Between Tool and Work Surface)

Supply Voltage given Gap between Tool and Work Surface

Go Supply Voltage = Gap Between Tool and Work Surface*Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed/(Current Efficiency in Decimal*Electrochemical Equivalent)

Gap between Tool and Work Surface

Go Gap Between Tool and Work Surface = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Specific Resistance of The Electrolyte*Work Piece Density*Feed Speed)

Specific Resistivity of Electrolyte given Supply Current

Go Specific Resistance of The Electrolyte = Area of Penetration*Supply Voltage/(Gap Between Tool and Work Surface*Electric Current)

Gap between Tool and Work Surface given Supply Current

Go Gap Between Tool and Work Surface = Area of Penetration*Supply Voltage/(Specific Resistance of The Electrolyte*Electric Current)

Gap Resistance between Work and Tool

Go Resistance of Gap Between Work and Tool = (Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface)/Cross Sectional Area of Gap

Specific Resistance of Electrolyte

Go Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface

Cross-Sectional Area of Gap

Go Cross Sectional Area of Gap = (Specific Resistance of The Electrolyte*Gap Between Tool and Work Surface)/Resistance of Gap Between Work and Tool

Width of Equilibrium Gap

Go Gap Between Tool and Work Surface = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Specific Resistance of The Electrolyte

Specific Resistance of Electrolyte Formula

Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface
r_e = (R*A_Gap)/h

What is Faraday's I law of electrolysis ?

The first law of Faraday’s electrolysis states that the chemical change produced during electrolysis is proportional to the current passed and the electrochemical equivalence of the anode material.

How to Calculate Specific Resistance of Electrolyte?

Specific Resistance of Electrolyte calculator uses Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface to calculate the Specific Resistance of The Electrolyte, The Specific resistance of electrolyte formula is defined as the resistivity of the electrolyte used in the ECM. Specific Resistance of The Electrolyte is denoted by r_e symbol.

How to calculate Specific Resistance of Electrolyte using this online calculator? To use this online calculator for Specific Resistance of Electrolyte, enter Resistance of Gap Between Work and Tool (R), Cross Sectional Area of Gap (A_Gap) & Gap Between Tool and Work Surface (h) and hit the calculate button. Here is how the Specific Resistance of Electrolyte calculation can be explained with given input values -> 300 = (0.012*0.000625)/0.00025.

FAQ

What is Specific Resistance of Electrolyte?

The Specific resistance of electrolyte formula is defined as the resistivity of the electrolyte used in the ECM and is represented as r_e = (R*A_Gap)/h or Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface. Resistance of Gap between Work and Tool, often referred to as the "gap" in machining processes, depends on various factors such as the material being machined, the tool material and geometry, The Cross Sectional Area of Gap is defined as the cross-sectional area of the equilibrium gap which is required to maintain the desired electrolytic effect between tool and workpiece & The Gap between Tool and Work Surface is the stretch of the distance between Tool and Work Surface during Electrochemical Machining.

How to calculate Specific Resistance of Electrolyte?

The Specific resistance of electrolyte formula is defined as the resistivity of the electrolyte used in the ECM is calculated using Specific Resistance of The Electrolyte = (Resistance of Gap Between Work and Tool*Cross Sectional Area of Gap)/Gap Between Tool and Work Surface. To calculate Specific Resistance of Electrolyte, you need Resistance of Gap Between Work and Tool (R), Cross Sectional Area of Gap (A_Gap) & Gap Between Tool and Work Surface (h). With our tool, you need to enter the respective value for Resistance of Gap Between Work and Tool, Cross Sectional Area of Gap & Gap Between Tool and Work Surface and hit the calculate button. You can also select the units (if any) for Input(s) and the Output as well.

How many ways are there to calculate Specific Resistance of The Electrolyte?

In this formula, Specific Resistance of The Electrolyte uses Resistance of Gap Between Work and Tool, Cross Sectional Area of Gap & Gap Between Tool and Work Surface. We can use 2 other way(s) to calculate the same, which is/are as follows -

Specific Resistance of The Electrolyte = Area of Penetration*Supply Voltage/(Gap Between Tool and Work Surface*Electric Current)
Specific Resistance of The Electrolyte = Current Efficiency in Decimal*Supply Voltage*Electrochemical Equivalent/(Gap Between Tool and Work Surface*Work Piece Density*Feed Speed)

Home

FREE PDFs

🔍 Search